Yamaha TX6n, Specifications

Page: 1 / 4

415 461
30
429
432
17
405
10
41
480
88
This document is printed on
chlorine-free (ECF) paper with soy ink.
For details please contact:
Printed in Japan
LPA564
Dimensions
unit : mm
GENERAL SPECIFICATIONS
TX6n TX5n TX4n
Output Power (W)
120V(US) 230V(EU)
* 1
120V(US) 230V(EU)
* 1
120V(US) 230V(EU)
* 1
2Ω per channel 2750 2750 2500 2500 2200 2200
4Ω per channel
3000 3000 2200 2300 1900 2000
8Ω per channel 1800 1800 1300 1300 1100 1100
1kHz 4Ω bridge 5500 5500 5000 5000 4400 4400
THD+N=1% 8Ω bridge 6000 6000 4400 4600 3800 4000
1kHz 2Ω per channel 4100 4120 3480 3600 2990 3050
20mS burst 4Ω bridge
8200 8240 6960 7200 5980 6100
Constant STEREO mode:
-
100V line,
-
voltage line Ω 1250W / 8Ω Ω
BRIDGE mode:
-
200V line,
-
Ω 2500W / 16Ω Ω
SN ratio
20Hz-20kHz (DIN AUDIO)
108dB 107dB 106dB
Power Stand-by 20W
consumption (W) Idle 100W
1/8 *
2
(2ΩΩ/ Pink noise) 1800W 1600W 1500W
All Models
THD+N
20Hz-20kHz,
Half Power RL=4
Ω
, 8
Ω
0.2%
Intermodulation Distortion
60Hz: 7kHz, 4:1, Half Power *
2
0.25%
Frequency response MAX +0.5dB
RL=8 Ω , Po=1W
TYP 0dB
10Hz-20kHz MIN -0.5dB
Channel Half Power RL=8
Ω
,1kHz
65dB
Separation
Att. max input 600 Ω shunt
Damping Factor RL=8 Ω 1kHz 800
Voltage Gain 43.8dB ~ 19.8dB, 0.1dB step
Maximum Input Voltage +24dBu*
4
Input Impedance 20kΩ (balanced) 10kΩ (unbalanced)
Controls
Front Panel POWER switch (push on / push off),
Rotary encoder x 2, Function button x 4,
HOME button x 1, EXIT button x 1,
ENTER button x 1, Mute button x 2
Connectors Analog input In XLR-3-31 type x 2
Thru XLR-3-32 type x 2
AES/EBU input/output In XLR-3-31 type x 1 (2 channels, 24-bit 96kHz ~ 44.1kHz)
Thru XLR-3-32 type x 1 (2 channels)
Out XLR-3-32 type x 1 (2 channels, 24-bit 96kHz ~ 44.1kHz)
Speaker output Neutrik ® SPEAKON ® NL4 x 2,
5-way binding post x 2 pairs
Ethernet RJ45 x 1
Fault output Euroblock connector (3P) x 1
Indicators IDENTIFY, NETWORK, PROTECTION, BRIDGE,
PARALLEL, POWER, STANDBY, MUTE, ALERT,
CLIP, SIGNAL,
Load protection POWER switch on / off mute,
DC-fault: Amplifier shuts down automatically.
clip limiting: THD ≥ 0.5%
Amplifier protection Thermal: Mute the output (heatsink temp ≥ 90°C)
(return automatically.).
VI limiter (RL ≤ 1ΩΩ) : Limit the output
Power supply protection Thermal: Amplifier shuts down automatically. (heatsink
temp ≥ 100°C)
Cooling Variable speed fan: x 2
Power requirements US : 120V (60Hz) 30A Twist lock connector
EU : 220V ~ 230V (50Hz / 60Hz)
Dimensions(W×H×D) 480 x 88 x 461mm (18.9” x 3.46” x 18.1” : 2U)
Weight 16.0kg (35 lbs)
Accessory Handle x 2 (with flat-head screw x 4),
Euroblock connector (3P) x 1, Owner's Manual
Specifications and appearance are subject to change without notice.
(*1) Output power depends on the power supply voltage. These figures are based on 230V.
If the power supply voltage is 220V, output power can be 8% less than the power shown in the spreadsheet.
Output power can be 7% more in case of 240V.
(*2) 1/8 power = 9dB below rated power
(*3) Half power = 3dB below rated power
(*4) 0dBu = 0.775Vrms
1/8 = Power consumption at 1/8 maximum output power
Neutrik ® and Speakon ® are trademarks of Neutrik ® .
All trademarks used are properties of their respective owners.
P O W E R A M P L I F I E R S
High Power Touring Amplifiers
with Internal DSP
and Advanced Networking Capabilities