Bn 00 xx 20 xx
Card2 Voice(multi)
Card3 Voice(multi)
Card4 Voice(multi)
Internal1 Perf(multi)
Internal2 Perf(multi)
Card1 Perf(multi)
Card2 Perf(multi)
Data
00,36
00,39
00,42
00,80
00,83
00,81
00,84
When the mode is set to off the program change is not transmitted.
When the mode is set to table, the conversion format contained in the program transmission table is
applied and transmitted.
1.2.1.5 Program change
Program change is transmitted, when a voice is selected in voice mode, when a performance is
selected in performance mode.
Program change No. is assigned as shown below in accordance with the mode.
1.2.2.3 Program change
When a program change message is received, the SY85 performs the following operations.
Three types of reception modes can be set with the system setup.
1 ) o f f :
Program change is not received.
2 ) normal:
In each play mode, the program No. changes in accordance with 00 〜 63 of the current
mode.
The program bank change is not received.
3) direct:
In voice mode, voice A1 〜 H8 correspond to the program change data 00 〜 63. INT1,
INT2 and CARD change in accordance with the program bank change.
Program change data 64 〜 127 is not received. In performance mode, performance A1 〜
H8 correspond to program change data 00 〜 63. Int1, Int2, and CARD change in accor
dance with the program bank change.
Program change data 64 〜 127 are not received.
In Multi mode, each INST program changes in accordance with the above.
Refer to during transmission for the bank change.
4) table:
Reception applies to 3) direct.
Transmission is carried out in accordance with the PROGRAM CHANGE TABLE.
1.2.2.4 Pitch bend
Pitch bend is received only on the MSB side.
1.2.2.5 After touch
After touch is received in accordance with the reception channel of each mode.
1.2.2.6 Channel mode message
2
Data
Voice
Internal1
0〜63
00〜63
Internal2
0〜63
00〜63
Internal3
0〜63
00〜63
Internal4
0〜63
00〜63
Card1
0〜63
00〜63
Card2
0〜63
00〜63
Card3
0〜63
00〜63
Card4
0〜63
00〜63
Performance
Internal1
0〜63
00〜63
Internal2
0〜63
00〜63
Card1
0〜63
00〜63
Card2
0〜63
00〜63
When the mode is set to off the program change is not transmitted.
When the mode is set to table, the conversion format contained in the program transmission table is
applied and transmitted.
1.2.1.6 Pitch bend
Pitch bend is transmitted with a resolution of 7 bits.
1.2.1.7 After touch
After touch is output when it is operated.
1.2.1.8 Channel mode message
Channel mode message is not transmitted.
1.2.2 Reception
1.2.2.1 Note Off
Reception note range
= C-2 〜 G8
Velocity range
= not received.
1.2.2.1 Note On/Off
Reception note range
= C-2 〜 G8
Velocity range
= 0 〜 127
1.2.2.2 Control change
The parameters in the table below can be controlled by MIDI.
cntrl#
parameter
data rng
1
Modulation wheel
0 〜 127
4
Foot control
0 〜 127
7
Foot Volume
0 〜 127
10
Pan
0 〜 127
0〜119
Volume
0 〜 127
1〜120
Effect Param1
0 〜 127
1〜120
Effect Param2
0 〜 127
16〜19
CS Param
0 〜 127
64
Sustain Switch
0 , 127
Pan is received only when MULTI is generated.
cntrl#
parameter
data rng
120
All Sound Off
0
121
Reset All Controller
0
123
All Notes Off
0
1.2.3 Configuration of keyboard section and tone generator
KBD
transmit ch
→ MIDI OUT
omni
(voice)
or rcv ch (multi)
voice rcv ch
(voice)
or rcv ch (multi)
TONE GENERATOR
○
○
local on/off
MIDI IN →
Note 1) In voice mode, sound is generated even if the Voice receive channel and the Keyboard Trans.
channel do not match.
Note 2) Note On from the keyboard and Note On from MIDI are distinguished. Controller information
from the keyboard and controller information from the MIDI (control change, after touch, pitch
bend, etc.) are not distinguished except for sustain switch.
