manualshive.com logo in svg

Yamaha SXV70G, Owner'S Manual

Share
Download
Yamaha SXV70G Owner'S Manual Download Page 90

11-2

ESU00231 

Chassis

CS-03E

SXV70/SXV70ER

Drive track and suspension:

Track

Molded rubber, fiber glass rod reinforced

Width

381 mm (15.0 in)

Track deflection

25–30 mm (0.98–1.18 in)/
100 N (10 kg, 22 lb)

Length on ground

752 mm (29.6 in)

Suspension type

Slide Rail Suspension

Drive sprocket

Quadruple polyethylene, 9 teeth

Transmission:

Type

Automatic centrifugal engagement, infinite-
ly variable 3.8:1–1:1

Sheave distance

Primary sheave center-to-secondary 
sheave center

Approx. 268.5 mm (10.57 in)

Primary sheave bolt center-to-sec-
ondary sheave bolt center

Approx. 269.5 mm (10.61 in)

Sheave offset

Secondary sheave

Front side

Approx. 14 mm (0.55 in): SXV70
Approx. 19 mm (0.75 in): SXV70ER

Rear side

Approx. 12 mm (0.47 in): SXV70
Approx. 17 mm (0.67 in): SXV70ER

Engagement speed

∗

Approx. 3,900 r/min

Shift speed

∗

Approx. 8,400 r/min

Drive chain

Silent chain enclosed in oil bath

Reduction ratio

38/22 (1.73)

Fuel tank:

Tank capacity

44.3 L (9.7 lmp gal, 11.7 US gal)

Oil tank:

Tank capacity

3.0 L (2.6 lmp qt, 3.2 US qt)

Brake:

Type

Hydraulic disc type (ventilated disc)

Operation

Handle lever, left hand operated

Throttle:

Operation

Handle lever, right hand operated

∗

 Subject to change according to elevation settings.

U8EK10.book  Page 2  Tuesday, June 26, 2001  4:35 PM

Summary of Contents for SXV70G

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands