background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-7

6

* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

NOTE:

From 19000 mi (31000 km) or 36 months, repeat the maintenance intervals starting from 7000 mi (11000 km) or 12 months.

EAU17620

NOTE:

The air filter needs more frequent service if you are riding in unusually wet or dusty areas.

Hydraulic brake system

• When disassembling the master cylinder or caliper cylinder, always replace the brake fluid. Check the brake fluid level

regularly and fill as required.

• Replace the oil seals on the inner parts of the master cylinder and caliper cylinder every two years.
• Replace the brake hoses every four years or if cracked or damaged.

26

*

Throttle grip hous-
ing and cable

• Check operation and free play.
• Adjust the throttle cable free play 

if necessary.

• Lubricate the throttle grip housing 

and cable.

27

*

Lights, signals and 
switches

• Check operation.
• Adjust headlight beam.

No.

ITEM

ROUTINE

INITIAL

ODOMETER READINGS

600 mi 

(1000 km) 

or 

1 month

4000 mi 

(6000 km) 

or 

6 months

7000 mi 

(11000 km) 

or 

12 months

10000 mi 

(16000 km) 

or 

18 months

13000 mi 

(21000 km) 

or 

24 months

16000 mi 

(26000 km) 

or 

30 months

U2UJ1GE0.book  Page 7  Friday, May 11, 2007  10:23 AM

Summary of Contents for Star XV250X



































































































Reviews: