Yamaha Star XV19MY Owner'S Manual Download

Page: 70 / 94

PERIODIC MAINTENANCE AND ADJUSTMENT

7-28

4. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

5. Connect the coupler, and then in-

stall the headlight bulb holder cov-
er by turning it clockwise.

To replace the low beam headlight bulb

1. Disconnect the headlight coupler,

and then remove the burnt-out
bulb by turning it counterclock-
wise.

2. Install a new bulb by turning it

clockwise.

3. Connect the headlight coupler.

Installing the headlight unit

1. Install the headlight unit by install-

ing the screws.

2. Connect the coupler to the head-

light body cover.

3. Install the headlight body cover by

installing the bolts.

4. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU24181

Tail/brake light

This model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.

1. Headlight coupler
2. Headlight bulb

U1D713E0.book Page 28 Thursday, May 8, 2008 4:19 PM

Summary of Contents for Star XV19MY































































































Search results

Summary of Contents for Star XV19MY

Reviews:

Related manuals for Star XV19MY

Brands by name

Popular brands

Yamaha Star XV19MY, Owner'S Manual

Search results

Summary of Contents for Star XV19MY

Reviews:

Related manuals for Star XV19MY

Brands by name

Popular brands