background image

FOR YOUR SAFETY – PRE-OPERATION CHECKS

5-1

5

EAU15596

Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection
and maintenance procedures and schedules described in the Owner’s Manual.

WARNING

EWA11151

Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.

Before using this vehicle, check the following points:

ITEM

CHECKS

PAGE

Fuel

• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
• Check the fuel tank breather/overflow hose for obstructions, cracks or damage, 

and check the hose connection.

4-11, 4-13

Engine oil

• Check oil level in oil tank.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.

7-10

Transfer case oil

• Check vehicle for oil leakage.

7-13

Front brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

7-18, 7-19

U2C514E0.book  Page 1  Tuesday, September 8, 2009  10:12 AM

Summary of Contents for Star XV19CTSZ 2009









































































































Reviews: