background image

Read this before use

ASSEMBLY

INSTRUCTIONS

SPEAKER STAND

SPS-30MMS

Thank you for selecting the Yamaha SPS-30MMS speaker stand.

YAMAHA  ELECTRONICS  CORPORATION,  USA

  6660  ORANGETHORPE  AVE.,  BUENA  PARK,  CALIF.  90620,  U.S.A.

YAMAHA  CANADA  MUSIC  LTD.

  135  MILNER  AVE.,  SCARBOROUGH,  ONTARIO  M1S  3R1,  CANADA

YAMAHA  ELECTRONIK  EUROPA  G.m.b.H. 

 SIEMENSSTR.  22-34,  25462  RELLINGEN  BEI  HAMBURG,  GERMANY

YAMAHA  ELECTRONIQUE FRANCE  S.A.

  RUE  AMBROISE  CROIZAT  BP70  CROISSY-BEAUBOURG  77312  MARNE-LA-VALLEE  CEDEX02,  FRANCE

YAMAHA  ELECTRONICS  (UK)  LTD.

  YAMAHA  HOUSE,  200  RICKMANSWORTH  ROAD  WATFORD,  HERTS  WD18 7GQ,  ENGLAND

YAMAHA  SCANDINAVIA  A.B.

  J  A  WETTERGRENS  GATA  1,  BOX  30053,  400  43  VÄSTRA  FRÖLUNDA,  SWEDEN

YAMAHA  MUSIC  AUSTRALIA  PTY,  LTD.

  17-33  MARKET  ST.,  SOUTH  MELBOURNE,  3205  VIC.,  AUSTRALIA

PRECAUTIONS

This speaker stand is only for the speaker systems
listed in “USABLE SPEAKERS” below. Do not use
the speakers other than these listed.

To prevent the speaker from falling, use the screws
and parts provided with the stand.

To prevent the speaker stand from falling over,
select a location which is flat and stable.

To avoid accidents resulting from tripping over
loose speaker cables and to prevent the speaker
stand from falling over, fix the speaker cables to the
wall, etc.

Do not let the children lean on the stand as this
might cause the serious accidents resulting from
the falling over of the speaker stand.

To prevent the speaker stand from discoloring and
warping, keep the speaker stand away from the stoves
and places where it will be exposed to direct sunlight,
etc.

Do not attempt to clean the speaker stand with
chemical solvents as this might damage the finish.
Use a clean, dry cloth.

When moving the speaker and stand, be sure to hold
the support detached from the speaker.

Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or installation
of speakers.

 DIMENSIONS

Top view

Front view

NS-10MMT (NS-10MMTS)

NX-430P

(the main and rear speakers included in the NS-P430/
NS-P436 speaker package)

NX-S20

(the front and rear speakers included in the AVX-S20 home
theater sound system)

NS-M125

NS-M225

NX-S30

(the satelite speakers included in the AVX-S30 home theater
sound system)

 USABLE SPEAKERS

Printed in China   WG59990

 ASSEMBLY PROCEDURES

Before beginning assembly, check the parts list and make sure all the parts are included.

 ASSEMBLY FIGURE

For speakers with screw holes at the left and right of the
speaker base.

For speakers with screw holes at the front and rear of
the speaker base.

 PARTS LIST

NAME

QUANTITY

1

Binding tapping screw (4 x 14 mm)

6

2

 Hexagon socket set screw

3 + 1 spare

3

 Binding machine screw (4 x 12 mm)

2

4

 Washer

2

5

 Binding machine screw (6 x 14 mm)

2

6

 Pad

4

7

 Wrench (hexagonal)

1

8

 Gasket

2

.

ASSEMBLY PROCEDURES

(You will need a screwdriver for assembly.)

1.  Attaching the base and support.

Pass the support through the hole from the bottom of the
base, and fasten the binding tapping screws 

1

.

 Fix the support so that the holes for the screws comes to

the rear side.

 Do not overtighten the binding tapping screws 

1

.

Doing so may damage the screws or assembly.

2. Attaching the pole and support.

Insert the pole to the support, and fasten the hexagon
socket set screws 

2

 into the three holes on the

support using the included wrench 

7

.

The line on the pole shows the limit of the stand height.
Do not use the stand pulling out the pole above from this
line. The hexagon socket set screw 

2

 of the lower side

becomes ineffective and the fixation becomes unstable.

3. Attaching the pads.

Put the pads 

6

 to the four corners on the bottom of the

base to prevent the stand from moving rickety.

4. Attaching the gaskets.

Put the gaskets 

8

 to the both sides of the plate.

5. Wiring the speaker cables.

Insert the speaker cables to the hole on the plate, and pass
through the pole. Aligned them to the grooved part on the
bottom of the base.

6. Attaching the speakers.

Line up the holes on the bottom of the speaker and the
center holes on the both sides of the plate. Depending on
the speakers, choose either the binding machine screws 

3

(4 x 12mm) or the binding machine screws 

5

 (6 x 14mm) to

fasten them into the holes.

■ 

If the speaker has 4mm holes on the bottom:

Fasten the binding machine screws 

(4 x 12mm) into

the holes with a screwdriver putting the supplied washers
between the screws and the plate.

■ 

If the speaker has 6mm holes on the bottom:

Fasten the binding machine screws 

(6x 14mm) into the

holes with a screwdriver.

Note

 After assembly is complete, always loosen the 3

hexagon socket set screws 

2

 before adjusting

speaker height and direction.

 In order to ensure that the speakers do not fall, always

hold the speakers during the assembly process.

618-868 (24-5/16"-34-3/16")

278 (11")

64

 (2-1/2")

25 (1")

80

 (3-3/16")

320

 (12-5/8")

320

 (12-5/8")

60

 (2-3/8")

8

Speaker cable

Speaker

8

4

4

5

3

5

3

1

1

6

6

Base

2

Support

2

7

3

5

5

3

4

4

Limit of the
stand height

Pole

8

8

Plate

Speaker cable

Speaker

© 2005                                         All rights reserved.

 SPECIFICATIONS

Dimensions (W x H x D)

:

320 x 618 – 868 x 320 mm
(12-5/8” x 2 -5/16”
– 34-3/16” x 12-5/8”)

Weight

:

2.4 kg (5 lbs. 4 oz.)

Pass the speaker
cable through the
hole on the plate.

Use the binding machine
screw 

3

 or 

5

Use the binding
machine screw

3

 or 

5

unit: mm(inch)

SPS-30MMS (J/EX)

10/4/05, 10:26 PM

1

Summary of Contents for SPS-30MMS

Page 1: ...てネジ やネジ穴を破損しないように注意してください 2 ポールとサポートの取り付け ポールをサポートの上から入れて サポート上部にある穴 3ケ所 にそれぞれ2六角穴止めネジを差し込み 必ず7六角レンチを使ってネジを締めてください ポールに高さの限界を示すラインがついてます そのライ ンより上に引き出した位置で使用しないでください 2六角穴止めネジの3個の内 下側のネジがきかな くなります 3 パッドの貼り付け ガタつき防止のため 6パッドを必ずベースの底面四隅に 貼ってください 4 パッキンの貼り付け 8パッキンを必ずポールのプレート スピーカー取付面 の両側に貼ってください 5 スピーカーケーブルの配線 スピーカーケーブルはプレートの抜き穴に入れ ポール の中を通してベースの底面の溝に沿って出してください 配線がすっきり見えます 6 スピーカーとスタンドの取り付け スピーカー底面のネジ穴...

Page 2: ...the speaker base PARTS LIST NAME QUANTITY 1 Binding tapping screw 4 x 14 mm 6 2 Hexagon socket set screw 3 1 spare 3 Binding machine screw 4 x 12 mm 2 4 Washer 2 5 Binding machine screw 6 x 14 mm 2 6 Pad 4 7 Wrench hexagonal 1 8 Gasket 2 ASSEMBLY PROCEDURES You will need a screwdriver for assembly 1 Attaching the base and support Pass the support through the hole from the bottom of the base and fa...

Reviews: