Yamaha S90, Owner'S Manual

Page: 103 / 139

103
Basics Section Quick Guide Reference Appendix
115 OutputSel Output Select Determines the specific output(s) for the individual part (Performance/Mixing Part Edit). Determines the specific output(s) for the
individual Drum key signal (Drum Key Edit). *16
*46
116 (InsEF)
Insertion Effect
Indicates whether the Insertion effect is applied or not for each part. This is for display purposes only and cannot be set here.
117 ElementSw
Controller Set 1-6 Element
Switch
Determines whether or not the selected controller affects each individual element.
“-”...disabled.
55 *47
118 Source
Controller Set 1-6 Source
Determines which panel controller is to be assigned and used for the selected Set. This controller then is used to control the
parameter set in Destination below.
55
*48
*49
119 Dest
Controller Set 1-6
Destination
Determines the parameter that is controlled by the Source
controller (above).
55 *50
120 Depth
Controller Set 1-6 Depth
Determines the degree to which the Source controller affects the Destination parameter.
55
121 Filter
MW/AT(CAT)/AC(AC1)
Filter Control
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) over the filter cutoff
frequency.
122 PMod
MW/AT(CAT)/AC(AC1)
LFO Pitch Modulation
Depth
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) has over pitch
modulation (vibrato effect).
123 FMod
MW/AT(CAT)/AC(AC1)
LFO Filter Modulation
Depth
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) has over filter cutoff
modulation (wah effect).
124 AMod
MW/AT(CAT)/AC(AC1)
LFO Amplitude Modulation
Depth
Determines the depth of control of the Modulation Wheel ([SF2])/Aftertouch ([SF3])/Assignable Controller ([SF4]) has over amplitude
modulation (tremolo effect).
125 Pitch (AT) AT (CAT) Pitch Control Determines the depth of control of keyboard aftertouch over pitch. You can set a value (in semitones) of up to two octaves.
126 Src
AC Source
(AC1 Control Number)
Determines the MIDI Control number used to control the filter, PMod, FMod, and Amod.
127 (ARP) Switch/Hold Arpeggio Switch/Hold
Control Number Determines the Control Number that controls the Arpeggio playback on/off and Arpeggio Hold on/off.
128 ASA/ASB
Assignable A/B Slider
Control Number
Determines the Control number to be controlled by the ASSIGN A/B sliders. This is available when controlling an external MIDI
device.
129 Dest
Assignable A/B Slider
Destination
Determines the function to be controlled by the Control Change number set above. See the separate Data List.
*50
130 FS
FS Control Number/
FS Function Assignment
Assign a specific function and control number to the Footswitch.
56 *51
131 Set Remote
Template Type Set Remote Mode
Template Type Select the template for your particular sequence software.
57
132 BankMSB/LSB
Bank Select MSB/LSB
Select the Voice for each zone by specifying these three MIDI messages. Refer to the Voice List in the separate Data List.
133 PgmChange Program Change
(Program Number 1-128)
134 CtrlSlider
Control Slider Control
Number
Determine which Control numbers are used for the Sliders for each zone. These settings are available only when the ZoneSwitch
(Master Play Mode [F2] ) is set to on and the CONTORL FUNCTION on the panel is set to “zone.”
53 *6
135 Level
Element Level
Adjusts the output level for the selected Element/drum key, letting you control the level balance among the Elements/keys.
Ref.
#
Display Parameter Name Explanation
Related
Page