Yamaha RX-V496, Owner'S Manual

Page: 21 / 63

17
English
B
ASIC OPERA
TION
AD
V
ANCED OPERA
TION
APPENDIX
INTR
ODUCTION
PREP
ARA
TION
IMPEDANCE SELECTOR Switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be
damaged.
If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide
to either position. If so, slide the switch to either position fully when this unit is in the standby mode.
Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only
when this unit is in the standby mode.
Connecting the Power Supply Cords
After completing all connections, connect the AC power
cord to an AC power outlet. Disconnect the AC power cord
if you will not use this unit for a long period of time.
■
AC OUTLETS (SWITCHED)
U.S.A. and Canada models .............................. 2 OUTLETS
Australia model .................................................. 1 OUTLET
Use these outlets to connect the power cords from your
components to this unit. The power to the AC OUTLET(S)
is controlled by this unit’s STANDBY/ON (or POWER).
These outlets will supply power to any connected
component whenever this unit is turned on. The maximum
power (total power consumption of components) that can be
connected to the AC OUTLET(S) is 100 W.
If you use left position right position
Center
speaker
The impedance must be 6
Ω
or higher.
The impedance must be 8
Ω
or higher.
Rear
speakers
The impedance of each
speaker must be 6
Ω
or
higher.
The impedance of each
speaker must be 8
Ω
or
higher.
If you use two pairs of main
speakers, the impedance of
each speaker must be 8
Ω
or
higher.
If you use two pairs of main
speakers, the impedance of
each speaker must be 16
Ω
or
higher.
[Canada model only]
The impedance of each
speaker must be 8
Ω
or
higher.
Main
speakers
If you use one pair of main
speakers, the impedance of
each speaker must be 4
Ω
or
higher.
If you use one pair of main
speakers, the impedance of
each speaker must be 8
Ω
or
higher.
CONNECTIONS
(U.S.A. model)
MAINS
MAIN A OR B : 4
Ω
MIN. /SPEAKER
A + B : 8
Ω
MIN. /SPEAKER
CENTER : 6
Ω
MIN. /SPEAKER
REAR : 6
Ω
MIN. /SPEAKER
MAIN A OR B : 8
Ω
MIN. /SPEAKER
A + B : I6
Ω
MIN. /SPEAKER
CENTER : 8
Ω
MIN. /SPEAKER
REAR : 8
Ω
MIN. /SPEAKER
SET BEFORE POWER ON
120 V 60Hz
100W MAX. TOTAL
SWITCHED
SWITCHED
(U.S.A. model)
To AC outlet
MAINS
MAIN A OR B : 4
Ω
MIN. /SPEAKER
A + B : 8
Ω
MIN. /SPEAKER
CENTER : 6
Ω
MIN. /SPEAKER
REAR : 6
Ω
MIN. /SPEAKER
MAIN A OR B : 8
Ω
MIN. /SPEAKER
A + B : I6
Ω
MIN. /SPEAKER
CENTER : 8
Ω
MIN. /SPEAKER
REAR : 8
Ω
MIN. /SPEAKER
SET BEFORE POWER ON
120 V 60Hz
100W MAX. TOTAL
SWITCHED
IMPEDANCE
SELECTOR
0103V49608-19_EN(UCA) 1/11/0, 11:25 AM 17