background image

12

1

2

3

To tune to higher frequencies, press right side once.
To tune to lower frequencies, press left side once.
* If the TUNING button is not pressed, in a while, the

automatic preset tuning begins automatically toward higher
frequencies.

The automatic preset tuning begins from the frequency
currently displayed.  Received stations are programmed to
A1, A2 ... A8 sequentially.
* If more than 8 stations are received, they are also 

programmed to the preset station numbers on other pages 
(B, C, D and E) in that order.

If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.

If, for example, you want to store the first received station to
C5, select “C5” by using the A/B/C/D/E button and the preset
station buttons after pressing the MEMORY button in step 2.
Then press the TUNING button. The first received station is
stored to C5, and next stations to C6, C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.

When the automatic preset tuning is finished

The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 11.

To recall a preset station

Simply follow the procedure of the section “To recall a preset
station” on page 11.

Notes

You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 11.

If the number of received stations is not enough to be stored
up to E8, the search is finished automatically after searching
through all frequencies.

With this function, only FM stations with sufficient signal
strength are stored automatically.  If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 11.

PRESET

MEMORY

AUTO TUNING

AUTOMATIC PRESET TUNING

You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially.  Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 11.

FM/AM

FM

MEMORY

MAN’L/AUTO FM

To store stations

Press and hold for
about 3 seconds.

Flashes.

1

2 3

DOWN

            

TUNING

            

UP

Summary of Contents for RX-595

















Reviews: