Yamaha RX-1130 RS Manual Download Page 25

Page: 25 / 28

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not

listed in the SYMPTOM column, disconnect the power cord and contact your dealer or service center for help.

The receiver fail!l to turn on when the

POWER

switch

is pressed.

No sound.

Sound "hums".

No picture.

stereo recep11ion is noisy.

There is distortic1n and clear reception cannot be

obtained even wiith a good

antenna.

A desired station cannot be tuned in with Auto tuning.

Power cord is not plugged in or is not completely inserted.

Incorrect output cord connections.

Incorrect receiver operation.

Incorrect cord connections.

Wrong video unit selected.

Video unit not turned on.

Because of the characteristics of FM stereo broadcasts, this is
limited to cases where the transmitter is far away or the

antenna input is poor.

There is multipath interference.

The station is too weak.

Weak signal or loose antenna connections.

There are continuous crackling and hissing noises.

These noise result from lightning, fluorescent lamps, motors,
thermostats and other electrical equipment.

There are buzzing and whining noises (especially in the

A television set is being used nearby.

evening).

Firmly plug in the power cord.

Connect cord properly. If the problem persists, the cables
rnay be defective.

Set the receiver controls to the correct input selection.

Firmly connect the audio plugs. If the problem persists, the

cord may be defective.

Connect the video plugs correctly.
Select correct video unit.

Turn video unit on.

Check the antenna connections.
Try using a multiple element FM antenna.

Adjust antenna placement to eliminate multipath interference.

Use Manual tuning rnode.
Use high quality directional FM antenna.

Tighten the AM loop antenna connections and rotate it for

best reception.

Use Manual tuning mode.

Use an outdoor antenna and a ground wire. This will help
some what but it is difficult to eliminate all noise.

Move the television away.

TROUBLESHOOTING

SYMPTON

CAUSE

REMEDY

Amplifier

Summary of Contents for RX-1130 RS





























Search results

Summary of Contents for RX-1130 RS

Reviews:

Related manuals for RX-1130 RS

Brands by name

Popular brands

Yamaha RX-1130 RS, Manual

Search results

Summary of Contents for RX-1130 RS

Reviews:

Related manuals for RX-1130 RS

Brands by name

Popular brands