Yamaha R6S Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 114

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-11

3

EAU12870

Shift pedal

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed con-
stant-mesh transmission equipped on
this motorcycle.

EAU12930

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a po-
sition adjusting dial. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the arrow mark on
the brake lever.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

1. Shift pedal

1. Brake lever

2. Arrow mark

3. Brake lever position adjusting dial
4. Distance between brake lever and handlebar

grip

1. Brake pedal

U4P612E0.book Page 11 Friday, May 11, 2007 3:58 PM

«
...
27
28
29
30
31
...
»

Summary of Contents for R6S



















































































































Reviews:

No comments

Related manuals for R6S

Brand: LAZER Pages: 13

Versaflo M Series

Brand: 3M Pages: 27

Speedglas 9100 Series

Brand: 3M Pages: 2

Brand: 3M Pages: 5

Brand: Öhlins Pages: 2

Mechatronics 35007-01

Brand: Öhlins Pages: 4

McPherson Strut MIR 5H02

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 4

Brand: VEB Pages: 63

Brand: Honda Pages: 158

Brand: Honda Pages: 140

Brand: GAS GAS Pages: 131

Brand: Megelli Pages: 83

Brand: Bosch Pages: 160

Brand: Arai Helmet Pages: 52

Brand: Arai Helmet Pages: 60

Brand: Yamaha Pages: 15

Brand: Yamaha Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands