background image

3

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements.  Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high quality
shielded cables.  Cable/s supplied with this product
MUST be used.  Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices.  Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that
interference will not occur in all installations.  If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:

Relocate either this product or the device that is being
affected by the interference.

Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product.  If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.

The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.

Caution: Read this before operating your unit

1

To assure the finest performance, please read this
manual carefully.  Keep it in a safe place for future
reference.

2

Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold.  Avoid sources of humming
(transformers, motors).  To prevent fire or electrical
shock, do not expose the unit to rain or water.

3

Do not operate the unit upside-down.  It may overheat,
possibly causing damage.

4

Never open the cabinet.  If something drops into the set,
contact your dealer.

5

Do not use force on switches, controls or connection
wires.  When moving the unit, first disconnect the power
plug and the wires connected to other equipment.
Never pull the wires themselves.

6

Do not attempt to clean the unit with chemical solvents;
this might damage the finish.  Use a clean, dry cloth.

7

Always set the VOLUME control to “– 

” before starting

the audio source play.  Increase the volume gradually to
an appropriate level after the play back has been
started.

8

To prevent lightning damage, pull out the power cord
and remove the antenna cable during an electrical
storm.

9

Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding
that the unit is faulty.

10

AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than
the outlet is rated to provide.

FCC INFORMATION

YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level.  One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without
affecting your sensitive hearing.  Since hearing
damage from loud sounds is often undetectable
until it is too late, YAMAHA and the Electronic
Industries Association’s Consumer Electronics
Group recommend you to avoid prolonged
exposure from excessive volume levels.

We Want You Listening For A Lifetime

Summary of Contents for R-V701 - AV Receiver
































Reviews: