background image

III

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level.  One that lets
the sound come through loud and clear without annoying
blaring or distortion – and, most importantly, without
affecting your sensitive hearing.

Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA
and the Electronic Industries Association’s
Consumer Electronics Group recommend you
to avoid prolonged exposure from excessive
volume levels.

FCC INFORMATION (for US customers only)

1.

IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!

This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements.  Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.

2.

IMPORTANT : 

When connecting this product to

accessories and/or another product use only high
quality shielded cables.  Cable/s supplied with this
product MUST be used.  Follow all installation
instructions.  Failure to follow instructions could void
your FCC authorization to use this product in the
USA.

3.

NOTE : 

This product has been tested and found to

comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.

This equipment generates/uses radio frequencies
and, if not installed and used according to the
instructions found in the users manual, may cause
interference harmful to the operation of other
electronic devices.

Compliance with FCC regulations does not guarantee that
interference will not occur in all installations.  If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:

Relocate either this product or the device that is being
affected by the interference.

Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient
the antenna.  If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product.  If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.

The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.

18

Servicing – Do not attempt to service this product
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.

19

Damage Requiring Service – Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:

a)

When the power-supply cord or plug is damaged,

b)

If liquid has been spilled, or objects have fallen
into the product,

c)

If the product has been exposed to rain or water,

d)

If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation,

e)

If the product has been dropped or damaged in
any way, and

f)

When the product exhibits a distinct change in
performance - this indicates a need for service.

20

Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.

21

Safety Check – Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.

22

Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.

23

Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.

NS-P230-236(UB)-PREc

02.5.8, 10:17 PM

3

Summary of Contents for NS-P230





















Reviews: