background image

MRX7-D Owner’s Manual

3

1.  IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions 
contained in this manual, meets FCC requirements. Modifi-
cations not expressly approved by Yamaha may void your 
authority, granted by the FCC, to use the product.

2. IMPORTANT:

 When connecting this product to accessories 

and/or another product use only high quality shielded cables. 
Cable/s supplied with this product MUST be used. Follow all 
installation instructions. Failure to follow instructions could 
void your FCC authorization to use this product in the USA.

3. NOTE:

 This product has been tested and found to comply 

with the requirements listed in FCC Regulations, Part 15 for 
Class “B” digital devices. Compliance with these require-
ments provides a reasonable level of assurance that your 
use of this product in a residential environment will not result 
in harmful interference with other electronic devices. This 
equipment generates/uses radio frequencies and, if not 
installed and used according to the instructions found in the 
users manual, may cause interference harmful to the opera-
tion of other electronic devices. Compliance with FCC regu-
lations does not guarantee that interference will not occur in 

all installations. If this product is found to be the source of 
interference, which can be determined by turning the unit 
“OFF” and “ON”, please try to eliminate the problem by using 
one of the following measures:
Relocate either this product or the device that is being 
affected by the interference.
Utilize power outlets that are on different branch (circuit 
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the 
antenna. If the antenna lead-in is 300 ohm ribbon lead, 
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory 
results, please contact the local retailer authorized to distrib-
ute this type of product. If you can not locate the appropriate 
retailer, please contact Yamaha Corporation of America, 
Electronic Service Division, 6600 Orangethorpe Ave, Buena 
Park, CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

(class B)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, 

Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Signal Processor

Model Name : MRX7-D

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including 

interference that may cause undesired operation.

See user manual instructions if interference to radio reception 
is suspected.

* This applies only to products distributed by 

YAMAHA CORPORATION OF AMERICA.

(FCC DoC)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING:

 THIS APPARATUS MUST BE EARTHED IMPOR-

TANT. The wires in this mains lead are coloured in accordance 
with the following code:

GREEN-AND-YELLOW : EARTH
BLUE

: NEUTRAL

BROWN

: LIVE

As the colours of the wires in the mains lead of this apparatus 
may not correspond with the coloured markings identifying the 
terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be 
connected to the terminal in the plug which is marked by the 
letter E or by the safety earth symbol

 or colored GREEN or 

GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the 
terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the 
terminal which is marked with the letter L or coloured RED.

(3 wires)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. 
Udskiftning må kun ske med batteri af samme fabrikat og type.  
Levér det brugte batteri tilbage til leverandoren. 

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batteri-
typ eller en ekvivalent typ som rekommenderas av apparattill-
verkaren. Kassera använt batteri enligt fabrikantens 
instruktion. 

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda 
paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. 
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de bat-

terij op het moment dat u het apparaat ann het einde van de 
levensduur of gelieve dan contact op te nemen met de verte-
genwoordiging van Yamaha in uw land.

• For the removal of the battery at the moment of the disposal 

at the end of life please consult your retailer or Yamaha rep-
resentative office in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small 

chemical waste.

(lithium disposal)

This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

* This applies only to products distributed 

by YAMAHA CORPORATION OF AMERICA.

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 
사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습
니다.

(class b korea)

(Perchlorate)

Summary of Contents for MRX7-D





































Reviews: