Yamaha MOX8 Data List Download

Page: 102 / 129

MOX6/MOX8 Data List

102

MIDI Data Format

(3-1-4) PROGRAM CHANGE

STATUS

1100nnnn (CnH)

n = 0 - 15 CHANNEL NUMBER

PROGRAM NUMBER

0ppppppp

p = 0 - 127

(3-1-5) CHANNEL AFTER TOUCH

STATUS

1101nnnn (DnH)

n = 0 - 15 CHANNEL NUMBER

VALUE

0vvvvvvv

v = 0 - 127 AFTER TOUCH VALUE

(3-1-6) PITCH BEND CHANGE

STATUS

1110nnnn (EnH)

n = 0 - 15 CHANNEL NUMBER

LSB

0vvvvvvv

PITCH BEND CHANGE LSB

MSB

0vvvvvvv

PITCH BEND CHANGE MSB

Transmitted with a resolution of 7 bits.

(3-2) CHANNEL MODE MESSAGES

STATUS

1011nnnn (BnH)

n = 0 - 15 CHANNEL NUMBER

CONTROL NUMBER

0ccccccc

c = CONTROL NUMBER

CONTROL VALUE

0vvvvvvv

v = DATA VALUE

(3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0)

All the sounds currently played including the channel messages such as note-on and hold-on in a certain
channel are muted when receiving this message.

(3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0)

Resets the values set for the following controllers.
PITCH BEND CHANGE

0 (center)

CHANNEL AFTER TOUCH

0 (minimum)

MODULATION

0 (minimum)

EXPRESSION

127 (maximum)

BREATH CONTROLLER

127 (maximum)

FOOT CONTROLLER

127 (maximum)

ASSIGN 1

0 (center)

ASSIGN 2

0 (center)

SUSTAIN SWITCH

0 (off)

SOSTENUTO SWITCH

0 (off)

RPN

Not assigned; No change

Doesn’t reset the following data:

PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, SUSTAIN LEVEL,

RELEASE TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT SEND LEVEL 1, EFFECT SEND

LEVEL 3, PORTAMENTO SWITCH, PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING

(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)

All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain
or Sostenuto is on, notes will continue sounding until these are turned off.

(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)

Performs the same function as when receiving ALL NOTES OFF.
Sets VOICE RECEIVE CHANNEL to “OMNI OFF,” channel 1.

(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)

Performs the same function as when receiving ALL NOTES OFF.
Sets VOICE RECEIVE CHANNEL to “OMNI ON.”

(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16)

Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16,
the channel will be Mode 4 (m = 1).
In the Voice mode, the mode can be Mode 2 (m = 1) according to VOICE RECEIVE CHANNEL.

(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)

Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode 3.
In the Voice mode, the mode can be Mode 1 according to VOICE RECEIVE CHANNEL.

(3-3) REGISTERED PARAMETER NUMBER

STATUS

1011nnnn (BnH)

n = 0 - 15 CHANNEL NUMBER

LSB

01100100 (64H)

RPN LSB

0ppppppp

p = RPN LSB

(Refer to the table as shown below.)

MSB

01100101 (65H)

RPN MSB

0qqqqqqq

q = RPN MSB

(Refer to the table as shown below.)

DATA ENTRY MSB

00000110 (06H)

DATA VALUE

0mmmmmmm

m = Data Value

DATA ENTRY LSB

00100110 (26H)

DATA VALUE

0lllllll

l = Data Value

First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.

RPN D.ENTRY

LSB MSB MSB LSB

PARAMETER NAME

DATA RANGE

00H 00H mmH ---

PITCH BEND SENSITIVITY

00H - 18H (0 - 24 semitones)

01H 00H mmH llH

MASTER FINE TUNE

{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8191*100/8192)

02H 00H mmH ---

MASTER COARSE TUNE

28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH --- ---

RPN RESET

RPN numbers will be left not designated.

The internal values are not affected.

(3-4) NON-REGISTERED PARAMETER NUMBER

There are no applicable parameters.

(3-5) SYSTEM REAL TIME MESSAGES

(3-5-1) ACTIVE SENSING

STATUS

11111110 (FEH)

Transmitted at every 200 msec.
Once this code is received, the instrument starts sensing. When no status nor data is received for over
approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the Sustain
Switch are forcibly turned off. Also, the values of the Controllers are reset to the default settings.

(3-6) SYSTEM EXCLUSIVE MESSAGE

(3-6-1) UNIVERSAL NON REALTIME MESSAGE

(3-6-1-1) GENERAL MIDI MODE ON

F0H 7EH 7FH 09H 01H F7H

The internal tone generator block will receive this message when the instrument is in the Song/Pattern mode.

(3-6-1-2) IDENTITY REQUEST (Receive only)

F0H 7EH 0nH 06H 01H F7H

(“n” = Device No. However, this instrument receives under “omni.”)

(3-6-1-3) IDENTITY REPLY (Transmit only)

F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H

dd; Device Number Code

MOX6: 44 06

MOX8: 45 06

(3-6-2) UNIVERSAL REALTIME MESSAGE

(3-6-2-1) MIDI MASTER VOLUME

F0H 7FH 7FH 04H 01H llH mmH F7H

Sets the MASTER VOLUME value.
The value “mm” is used to set the master volume (the value “ll” should be ignored).

(3-6-3) PARAMETER CHANGE

(3-6-3-1) NATIVE PARAMETER CHANGE, MODE CHANGE

11110000

Exclusive Status

01000011

YAMAHA ID

0001nnnn

Device Number

01111111

Model ID

00000000

Model ID

0aaaaaaa

aaaaaaa

Address High

0aaaaaaa

aaaaaaa

Address Mid

0aaaaaaa

aaaaaaa

Address Low

0ddddddd

ddddddd

Data

11110111

End of Exclusive

For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
See the following MIDI Data Table for Address and Byte Count.

(3-6-4) BULK DUMP

11110000

Exclusive Status

01000011

YAMAHA ID

0000nnnn

Device Number

01111111

Model ID

00000000

Model ID

0bbbbbbb

bbbbbbb

Byte Count

0bbbbbbb

bbbbbbb

Byte Count

0aaaaaaa

aaaaaaa

Address High

0aaaaaaa

aaaaaaa

Address Mid

0aaaaaaa

aaaaaaa

Address Low

Data

0ccccccc

ccccccc

Check-sum

11110111

End of Exclusive

See the following BULK DUMP Table for Address and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address,
Data and Check sum itself are added.

(3-6-5) DUMP REQUEST

11110000

Exclusive Status

01000011

YAMAHA ID

0010nnnn

Device Number

01111111

Model ID

00000000

Model ID

0aaaaaaa