manualshive.com logo in svg

Yamaha MOTIF XF6, Owner'S Manual

Share
Download
Yamaha MOTIF XF6 Owner'S Manual Download Page 78

MOTIF XF Owner’s Manual

78

Specifications

Keyboards 

MOTIF XF8
MOTIF XF7
MOTIF XF6

88 keys, Balanced Hammer Effect Keyboard (Initial Touch/Aftertouch)
76 keys, FSX Keyboard (Initial Touch/Aftertouch)
61 keys, FSX Keyboard (Initial Touch/Aftertouch)

Tone Generator 
block 

Tone Generator

AWM2, with Expanded Articulation

Polyphony

128 notes

Multi Timbral Capacity

16 Parts (internal), Audio Input Parts (A/D, FW*)

*1 stereo Part

Wave

741 MB (when converted to 16-bit linear format), 3,977 waveforms

Voice

Preset: 1,024 Normal  64 Drum Kits
GM: 128 Normal  1 Drum Kit
User: 128 x 4 (Bank 1: original, Bank 2 – 4: selected and copied from Preset bank) 
+ 32 Drum Kits (No. 1 – 8: original, No. 9 – 32: selected and copied from Preset bank) 

Performance

User: 128 x 4 (up to 4 Parts)

Filter

18 types

Effect System

Reverb x 9 types, Chorus x 22 types, Insertion (A, B) x 53 types x 8 Parts (up to 16 units), 
Vocoder x 1 (uses both Insertion Effect A and B blocks), Master Effect x 9 types 
(Preset settings for parameters of each effect type are provided as templates; total 320) 
Master EQ (5 bands), Part EQ (3 bands, stereo)

Sampling block

Samples

Up to 128 Waveforms (Multi Samples)
Up to 256 Key Banks per Waveform
Up to 512 Key Banks

Sampling Sources

Analog input L/R, Stereo output (Resampling)
FW (available when the FW16E has been installed)

A/D Conversion
D/A Conversion

24-bit, 64x oversampling
24-bit,128x oversampling 

Sample Data Bits

16

Sampling Frequency

44.1kHz, 22.05kHz, 11.025kHz, 5.5125kHz (Stereo/Mono)
Sampling Frequency via FW (when the FW16E has been installed): 44.1kHz (fixed)

Sampling Memory

Internal SDRAM: 128M

Sample Length

Mono: 32 MB
Stereo: 64 MB

Sampling Time

44.1kHz: 6 min. 20 sec.
22.05kHz: 12 min. 40 sec.
11.025kHz: 25 min. 20 sec.
5.5125kHz: 55 min. 40 sec.

*Mono/Stereo

Sample Format

Original format, WAV, AIFF

Sampling Sources

Analog input L/R, Stereo output (Resampling)
FW (available when the FW16E has been installed)

Sequencer block 

Note Capacity

Approx. 130,000 notes

Note Resolution

480 ppq (parts per quarter note)

Maximum Polyphony

124 notes

Tempo (BPM)

5 – 300

Recording type

Real time replace
Real time overdub (with the exception of the Pattern Chain)
Real time punch in/out (Song only)

Tracks

Pattern: 16 Phrase tracks
Pattern Chain: Pattern track, Tempo track, Scene track
Song: 16 sequence tracks (Loop on/off can be set for each track), Tempo track, Scene track

Patterns

64 Patterns (x 16 sections), Measures: 256 maximum
Mixing Voices: 16 Voices per Pattern and up to 256 Voices for all Patterns
Mixing Templates: 32 for all Songs and Patterns

Phrases

User Phrases: 256 per Pattern

Songs

64 Songs 
Mixing Voices: 16 Voices per Song and up to 256 Voices for all Songs
Mixing Templates: 32 for all Songs and Patterns

Summary of Contents for MOTIF XF6























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands