2
RDX-E700/NX-E700
RDX-E700
NX-E700
■
TO SERVICE PERSONNEL
1. Critical Components Information
Components having special characteristics are marked
Z
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
●
Meter impedance should be equivalent to 1500 ohms shunted
by 0.15
µ
F.
AC LEAKAGE
TESTER OR
EQUIVALENT
EQUIPMENT
UNDER TEST
INSULATING
TABLE
WALL
OUTLET
●
Leakage current must not exceed 0.5mA.
●
Be sure to test for leakage with the AC plug in both
polarities.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or
plastic (where applicable) components may also contain traces of chemicals found by the California Health and
Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR
ANY REASON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes
or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands
before handling food.
About Lead Free Solder /
無鉛ハンダについて
The P.C.B.s installed in this unit are soldered using the fol-
lowing solder.
本機に搭載されている基板のハンダ付けに使用されている
ハンダは下記の通りです。
SIDE A / A 面
SIDE B / B 面
MPEG P.C.B.
Lead Free Solder / 無鉛ハンダ
Lead Free Solder / 無鉛ハンダ
FRONT P.C.B.
−
Lead Free Solder / 無鉛ハンダ
MAIN P.C.B.
Lead Free Solder / 無鉛ハンダ
Lead Free Solder / 無鉛ハンダ
POWER SUPPLY UNIT
−
Lead Free Solder / 無鉛ハンダ
Side A
Side B
SMT
REFLOW
Process
MI
FLOW
Process
Solder Dip
Among some types of lead free solder currently available, it
is recommended to use one of the following types for the
repair work.
• Sn + Ag + Cu (tin + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
1. As the melting point temperature of the lead free solder is
about 30
°
C to 40
°
C (50
°
F to 70
°
F) higher than that of the
lead solder, be sure to use a soldering iron suitable to
each solder.
無鉛ハンダにはいくつかの種類がありますが、修理時には
下記のような無鉛ハンダの使用を推奨します。
・Sn+Ag+Cu （錫 + 銀 + 銅）
・Sn+Cu （錫 + 銅）
・Sn+Zn+Bi （錫 + 亜鉛 + ビスマス）
注意：
1. 無鉛ハンダの融点温度は通常の鉛入りハンダに比べ30〜
40 ℃程度高くなっていますので、それぞれのハンダに
合ったハンダごてをご使用ください。
All manuals and user guides at all-guides.com
