background image

 

PERIODIC MAINTENANCE AND MINOR REPAIR

 

6-29

 

1

2

3

4

5

6

7

8

9

 

enter the brake system, possibly caus-
ing it to become ineffective.
Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads
and/or brake system leakage. If the
brake fluid level is low, be sure to check
the brake pads for wear and the brake
system for leakage.
Observe these precautions:

 

 

When checking the fluid level,
make sure that the top of the brake
fluid reservoir is level.

 

 

Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.

 

 

Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.

 

 

Be careful that water does not en-
ter the brake fluid reservoir when

refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.

 

 

Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.

 

 

As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.

 

EAU22730

 

Changing the brake fluid 

 

Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

 

 

Oil seals: Replace every two
years.

 

 

Brake hoses: Replace every four
years.

 

Recommended brake fluid:

 

DOT 4

Summary of Contents for Majesty YP400W







































































































Reviews: