Yamaha Grizzly YFM35FGIX Owner'S Manual Download Page 22 | Manualshive

Page: 22 / 164

background image

4-3

4

If the warning light stays on, allow the engine to
cool. If the warning light stays on when the engine
is cool, have a Yamaha dealer check the electrical
circuit.

CAUTION:

ECB00010

●

The engine may overheat if the ATV is over-
loaded. In this case, reduce the load to spec-
ification.

●

Start the engine after making sure that the
warning light is out. Continuous use while
the warning light is on may cause damage to
the engine.

EBU17952

On-Command four-wheel-drive indicator light
“

”

This indicator light comes on when the On-Com-
mand four-wheel-drive switch is set to the “4WD”
position.

NOTE:

Due to the synchronizing mechanism in the differ-
ential gear case, the light may not come on until
the ATV starts moving.

EBU28341

On-Command differential gear lock indicator
light “

”

This indicator light and the On-Command four-
wheel-drive indicator light “

” come on when the

On-Command differential gear lock switch is set to
the “LOCK” position.

EBU18020

Speedometer

The speedometer shows the riding speed. This
speedometer is equipped with an odometer and a
tripmeter. The tripmeter can be reset to “0” with the
reset knob. Use the tripmeter to estimate how far
you can ride on a tank of fuel before going to re-
serve. This information will enable you to plan fuel
stops in the future.

U4S211E0.book Page 3 Friday, May 25, 2007 9:38 AM

«
...
20
21
22
23
24
...
»

Summary of Contents for Grizzly YFM35FGIX





































































































































































Reviews:

No comments

Related manuals for Grizzly YFM35FGIX

Brand: J&M Pages: 26

Brand: Snapper Pages: 82

Sportsman 9920629

Brand: Polaris Pages: 143

Brand: Ventrac Pages: 83

Brand: ODES Pages: 97

Brand: Dane Technologies Pages: 74

Brand: Baja motorsports Pages: 24

Quad Lander 250

Brand: Sym Pages: 223

Brand: KAYO MOTO Pages: 8

Brand: Cushman Pages: 176

Brand: Kipor Pages: 102

Brand: FERPINTA Pages: 14

Brand: Arctic Cat Pages: 124

2015 WILDCAT SPORT

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 84

Brand: Arctic Cat Pages: 177

Brand: Arctic Cat Pages: 190

DVX 90/90 UTILITY

Brand: Arctic Cat Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands