Yamaha GRIZZLY 350 YFM35GA Owner'S Manual Download Page 116

Page: 116 / 136

8-38

2. Connect the positive battery lead first, then

connect the negative battery lead by installing
their bolt.

NOTICE:

When installing the bat-

tery, the main switch must be off, and the
positive lead must be connected before
the negative lead.

[ECB01110]

3. Install the battery holding plate by installing

the bolts.

4. Install the seat. (See page 4-12.)

EBU25326

Replacing a fuse

The main fuse and the fuse box are located under
the seat. (See page 4-12.)

1. Positive battery lead (red)

2. Negative battery lead (black)

1. Main fuse

2. Spare main fuse
3. Fuse box

U5WH67E0.book Page 38 Thursday, June 3, 2010 2:10 PM

Summary of Contents for GRIZZLY 350 YFM35GA









































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35GA

Reviews:

Related manuals for GRIZZLY 350 YFM35GA

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35GA, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35GA

Reviews:

Related manuals for GRIZZLY 350 YFM35GA

Brands by name

Popular brands