Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download | Manualshive

Page: 114 / 138

background image

8-36

8

EBU28832

Checking and lubricating the brake
pedal

The operation of the brake pedal should be
checked before each ride, and the pedal pivot
should be lubricated if necessary.

TIP

To access the brake pedal pivot, remove panel A.
(See page 8-8.)

EBU24962

Checking the wheel hub bearings

The front and rear wheel hub bearings must be
checked at the intervals specified in the periodic
maintenance and lubrication chart. If there is play
in a wheel hub or if a wheel does not turn smoothly,
have a Yamaha dealer check the wheel hub bear-
ings.

EBU25102

Lubricating the steering shaft

The steering shaft must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU29183

Battery

This model is equipped with a VRLA (Valve Regu-
lated Lead Acid) battery. There is no need to check
the electrolyte or to add distilled water. However,
the battery lead connections need to be checked
and, if necessary, tightened.

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

U5UH65E0.book Page 36 Monday, June 16, 2008 10:34 AM

«
...
112
113
114
115
116
...
»

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35FGY

Pioneer SXS500M 2018

Brand: Honda Pages: 268

Brand: Baja motorsports Pages: 76

Trail Boss 330 Quadricycle

Brand: Polaris Pages: 119

Brand: FLEMING Pages: 6

Dodge Grand Caravan

Brand: Savaria Pages: 44

Brand: DAELIM Pages: 163

Brand: E-Z-GO Pages: 66

Brand: Baja motorsports Pages: 77

2013 RANGER RZR 570

Brand: Polaris Pages: 152

Brand: Samsung Pages: 172

Brand: Access Motor Pages: 65

EcoLight MPG585

Brand: Malone Pages: 9

Brand: Ultraflex Pages: 22

Brand: Polaris Pages: 135

Brand: Polaris Pages: 117

Brand: Polaris Pages: 121

Brand: Polaris Pages: 162

2014 RANGER 400

Brand: Polaris Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands