background image

10

VIBRATO SYSTEM  Locking Type

When changing strings it is necessary to cut off the ball ends of 

the strings.

Following is the procedure for changing strings and adjusting the 

vibrato system:

1)  Loosen the three clamp screws (A).
2)  Turn the peg to loosen the string being replaced.
3)  Loosen the lock screw (B) of the string being replaced.
4)  Remove the old string.
5)  Tighten the lock screw to lock the string in place, then roughly 

tune the string. Do not over tighten the lock screw. Over tight-

ening may result in damage.

6)  Make sure that the fine tuning screw (C) is in the middle of its 

range of travel.

7)  After tuning, rock the tremolo arm back and forth about three 

times then re-tune the instrument.

8)  If necessary, adjust the intonation and bridge angle.
9)  Tighten the three clamp screws (A) to lock the strings at the nut.
10) Use the fine-tuning screws (C) to precisely tune the instrument 

to the correct pitch.

Intonation Adjustment in Vibrato Bridge

1)  After loosening/detuning the strings you would like to adjust. 

Loosen the hexagonal screw (D) located in the front of each 

saddle using the supplied hexagonal wrench.

2)  Slide the saddles by hand to adjust the length of each string.
3)  When the intonation is correct, tighten the hexagonal screw (D)  

in front of each saddle to ensure that its position stays stationary. 

02_EG_om_en_0126.indd   10

16/01/26   14:29

Summary of Contents for GIGMAKER
















Reviews: