background image

INSTRUMENT AND CONTROL FUNCTIONS

4-21

4

EAU41941

EXUP system 

This model is equipped with Yamaha’s
EXUP (EXhaust Ultimate Power valve)
system. This system boosts engine
power by means of a valve that regu-
lates the inner diameter of the exhaust
pipe. The EXUP system valve is con-
stantly adjusted in accordance with the
engine speed by a computer-controlled
servomotor.

NOTICE

ECA15610

The EXUP system has been set and
extensively tested at the Yamaha
factory. Changing these settings
without sufficient technical knowl-
edge may result in poor perfor-
mance of or damage to the engine.

EAU15303

Sidestand 

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

TIP

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See page 4-22 for an explanation of
the ignition circuit cut-off system.)

WARNING

EWA10240

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

U1CA10E0.book  Page 21  Tuesday, November 24, 2009  1:41 PM

Summary of Contents for FZS10Z















































































































Reviews: