Yamaha FZ8NB Owner'S Manual Download

Page: 80 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-36

EAU24115

Replacing the tail/brake light
bulb

1. Remove the passenger seat. (See

page 4-14.)

2. Remove the tail/brake light bulb

socket (together with the bulb) by
turning it counterclockwise.

3. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

4. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the passenger seat.

EAU43004

Replacing a turn signal light
bulb

1. Remove the turn signal light unit

by removing the screw.

2. Remove the turn signal light bulb

socket (together with the bulb) by
turning it counterclockwise.

3. Remove the burnt-out bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the turn signal light unit by

installing the screw.

1. Tail/brake light bulb socket

1. Turn signal light unit

2. Screw

1. Turn signal light bulb socket

1. Turn signal light bulb

U39P11E0.book Page 36 Monday, August 1, 2011 5:00 PM

Summary of Contents for FZ8NB













































































































Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands

Yamaha FZ8NB, Owner'S Manual

Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands