Yamaha FZ8-N Owner'S Manual Download Page 86

Page: 86 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

6-36

5. Disconnect the headlight coupler,

then remove the headlight bulb
cover.

6. Unhook the headlight bulb holder,

then remove the burnt-out bulb.

7. Place a new headlight bulb into po-

sition, then secure it with the bulb
holder.

8. Install the headlight bulb cover,

then connect the headlight cou-
pler.

9. Connect the coupler, then insert

the projection on the headlight unit
into the grommet on the vehicle to
fit the headlight unit in its original
position.

10. Install the headlight unit bolts.
11. Install the bolt behind the headlight

unit.

12. Place the top cover in its original

position, and then install its bolts.

1. Coupler

1. Headlight coupler

2. Headlight bulb cover

1. Headlight bulb holder
2. Headlight bulb

1. Projection
2. Grommet

U39PE2E0.book Page 36 Thursday, November 8, 2012 9:24 AM

Summary of Contents for FZ8-N













































































































Search results

Summary of Contents for FZ8-N

Reviews:

Related manuals for FZ8-N

Brands by name

Popular brands

Yamaha FZ8-N, Owner'S Manual

Search results

Summary of Contents for FZ8-N

Reviews:

Related manuals for FZ8-N

Brands by name

Popular brands