Yamaha FZ1-SW Owner'S Manual Download

Page: 90 / 98

SPECIFICATIONS

8-1

Dimensions:

Overall length:

2140 mm (84.3 in)

Overall width:

770 mm (30.3 in)

Overall height:

1205 mm (47.4 in)

Seat height:

815 mm (32.1 in)

Wheelbase:

1460 mm (57.5 in)

Ground clearance:

135 mm (5.31 in)

Minimum turning radius:

3000 mm (118.1 in)

Weight:

With oil and fuel:

220.0 kg (485 lb)

Engine:

Engine type:

Liquid cooled 4-stroke, DOHC

Cylinder arrangement:

Forward-inclined parallel 4-cylinder

Displacement:

998.0 cm³

Bore

stroke:

77.0

53.6 mm (3.03

2.11 in)

Compression ratio:

11.50 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Type:

SAE10W30, SAE10W40, SAE15W40,
SAE20W40 or SAE20W50

Recommended engine oil grade:

API service SG type or higher, JASO
standard MA

Engine oil quantity:

Without oil filter cartridge replacement:

2.90 L (3.07 US qt) (2.55 Imp.qt)

With oil filter cartridge replacement:

3.10 L (3.28 US qt) (2.73 Imp.qt)

Cooling system:

Coolant reservoir capacity (up to the
maximum level mark):

0.25 L (0.26 US qt) (0.22 Imp.qt)

Radiator capacity (including all routes):

2.25 L (2.38 US qt) (1.98 Imp.qt)

Air filter:

Air filter element:

Oil-coated paper element

Fuel:

Recommended fuel:

Unleaded gasoline only

Fuel tank capacity:

18.0 L (4.76 US gal) (3.96 Imp.gal)

Fuel reserve amount:

3.4 L (0.90 US gal) (0.75 Imp.gal)

Fuel injector:

Manufacturer:

DENSO

Model/quantity:

297500-0300/4

Spark plug (s):

Manufacturer/model:

NGK/CR9EK

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

Clutch:

Clutch type:

Wet, multiple-disc

Transmission:

Primary reduction system:

Spur gear

Primary reduction ratio:

65/43 (1.512)

Secondary reduction system:

Chain drive

Secondary reduction ratio:

45/17 (2.647)

Transmission type:

Constant mesh 6-speed

Operation:

Left foot operation

-20 -10 0 10 20 30 40 50 ˚C

SAE 10W-30

SAE 15W-40

SAE 20W-40

SAE 20W-50

SAE 10W-40

U3C321E0.book Page 1 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

Summary of Contents for FZ1-SW



































































































Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands

Yamaha FZ1-SW, Owner'S Manual

Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands