Yamaha FZ1-SW Owner'S Manual Download | Manualshive

Page: 59 / 98

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-12

6

●

If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.

WARNING

EWA10380

Never attempt to remove the radiator
cap when the engine is hot.

5. Install the panel.

NOTE:

●

The radiator fans are automatically
switched on or off according to the
coolant temperature in the radia-
tor.

●

If the engine overheats, see page
6-37 for further instructions.

EAU33030

Changing the coolant

WARNING

EWA10380

Never attempt to remove the radiator
cap when the engine is hot.

The coolant must be changed at the in-
tervals specified in the periodic mainte-
nance and lubrication chart. Have a
Yamaha dealer change the coolant.

EAU40051

Replacing the air filter element

The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.

1. Remove the rider seat. (See page

2. Remove panels A and B. (See

3. Remove the cowling bolts, and

then pull the cowling off.

4. Remove the fuel tank bolts.

1. Cowling

2. Bolt

U3C321E0.book Page 12 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

«
...
57
58
59
60
61
...
»

Summary of Contents for FZ1-SW



































































































Reviews:

No comments

Related manuals for FZ1-SW

Brand: Öhlins Pages: 8

prodrive SUR 3A00

Brand: Öhlins Pages: 4

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 4

Brand: Kabuto Pages: 40

Brand: DAELIM Pages: 68

Brand: TB Pages: 8

HPS.08.473.10000/B

Brand: SW-Motech Pages: 4

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 5

Brand: Arai Helmet Pages: 52

Brand: Arai Helmet Pages: 60

HelmetTalk HTCS-3O

Brand: Nady Systems Pages: 2

HPS SafeGuard Series

Brand: Dräger Pages: 40

Brand: Malaguti Pages: 121

Brand: IL Motorsport Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands