background image

Maintenance

84

problem could cause severe engine
damage. Consult your Yamaha dealer
if the problem cannot be located and
corrected.

 [ECM01623]

14. Install the top cowling.
15. Dispose of used oil according to local

regulations.

TIP:

For more information on the disposal of
used oil, consult your Yamaha dealer.

Change the oil more often when operating
the engine under adverse conditions such
as extended trolling.

EMU29115

Inspecting wiring and connectors

Inspect that each connector is engaged se-
curely.

Inspect that each ground lead is properly
secured.

EMU32113

Checking propeller

WARNING

EWM01882

You could be seriously injured if the en-
gine accidentally starts when you are near
the propeller. Before inspecting, remov-
ing, or installing the propeller, place the
shift control in neutral, turn the main
switch to “

” (off) and remove the key,

and remove the clip from the engine shut-
off switch. Turn off the battery cut-off
switch if your boat has one.

Do not use your hand to hold the propeller
when loosening or tightening the propeller
nut. Put a wood block between the anti-cavi-
tation plate and the propeller to prevent the
propeller from turning.

ZMU08109

ZMU08110

U6EK70E0.book  Page 84  Friday, January 31, 2014  2:37 PM

Summary of Contents for FL115B













































































































Reviews: