Yamaha FJR1300S(C) Owner'S Manual Download

Page: 23 / 99

INSTRUMENT AND CONTROL FUNCTIONS

3-6

EAU12492

Windshield position adjusting
switch “

”

To move the windshield up, push this
switch in direction (a). To move the
windshield down, push the switch in di-
rection (b).

NOTE:

When the engine is turned off, the wind-
shield will automatically return to the
lowest position.

EAU12500

Horn switch “

”

Press this switch to sound the horn.

EAU12660

Engine stop switch “

”

Set this switch to “

” before starting

the engine. Set this switch to “

” to

stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.

EAU12710

Start switch “

”

Push this switch to crank the engine
with the starter.

CAUTION:

ECA10050

See page 5-1 for starting instruc-
tions prior to starting the engine.

EAU12763

Hazard switch “

”

With the key in the “ON” position, turn
this switch to “

” to turn on the hazard

lights (simultaneous flashing of all turn
signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.

CAUTION:

ECA10060

Do not use the hazard light for an ex-
tended length of time, otherwise the
battery may discharge.

1. Windshield position adjusting switch “

”

1. Hazard switch “

”

5JW11.book Page 6 Friday, May 9, 2003 4:03 PM

Summary of Contents for FJR1300S(C)




































































































Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands

Yamaha FJR1300S(C), Owner'S Manual

Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands