Yamaha FJR1300S(C) Owner'S Manual Download Page 39 | Manualshive

Page: 39 / 99

background image

OPERATION AND IMPORTANT RIDING POINTS

5-1

5

EAU15950

WARNING

EWA10270

●

Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.

●

Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.

●

Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.

EAU31950

Starting the engine

In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

●

The transmission is in the neutral
position.

●

The transmission is in gear with
the clutch lever pulled and the sid-
estand up.

WARNING

EWA10290

●

Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure
described on page 3-17.

●

Never ride with the sidestand
down.

1. Turn the key to “ON” and make

sure that the engine stop switch is
set to “

”.

CAUTION:

ECA12700

The oil level warning light, engine
trouble warning light and ABS warn-
ing light should come on for a few
seconds, then go off. If a warning

light does not go off, see page 3-2
for the corresponding warning light
circuit check.

2. Shift the transmission into the neu-

tral position.

NOTE:

When the transmission is in the neutral
position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical cir-
cuit.

3. Start the engine by pushing the

start switch.

NOTE:

If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the en-
gine more than 10 seconds on any one
attempt.

5JW11.book Page 1 Friday, May 9, 2003 4:03 PM

«
...
37
38
39
40
41
...
»

Summary of Contents for FJR1300S(C)




































































































Reviews:

No comments

Related manuals for FJR1300S(C)

Brand: R&G Pages: 14

Brand: X-lite Pages: 76

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 360

Brand: Yamaha Pages: 580

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 116

Tracer 9 GT 2021

Brand: Yamaha Pages: 126

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 87

Brand: Yamaha Pages: 94

Star XVS13CG 2015

Brand: Yamaha Pages: 98

Star XV250G 2015

Brand: Yamaha Pages: 88

Star XVS13CTD 2012

Brand: Yamaha Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands