Yamaha FAZER FZ6-SV 2006 Owner'S Manual Download Page 73

Page: 73 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-33

3. Remove the brake hose holder on

each side by removing the bolts.

4. Remove the brake caliper on each

side by removing the bolts.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

5. Pull the wheel axle out, and then

remove the wheel.

EAU33660

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Install the brake calipers by install-

ing the bolts.

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

4. Install the brake hose holders by

installing the bolts.

5. Take the motorcycle off the center-

stand so that the front wheel is on
the ground.

6. Tighten the wheel axle, the front

wheel axle pinch bolt and the
brake caliper bolts to the specified
torques.

7. Push down hard on the handlebar

several times to check for proper
fork operation.

1. Brake hose holder
2. Brake caliper

3. Brake caliper bolt

4. Bolt

Tightening torques:

Wheel axle:

72 Nm (7.2 m·kgf, 52 ft·lbf)

Front wheel axle pinch bolt:

19 Nm (1.9 m·kgf, 13 ft·lbf)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

U5VX22E0.book Page 33 Wednesday, September 14, 2005 11:42 AM

ProCarManuals.com

Summary of Contents for FAZER FZ6-SV 2006



























































































Search results

Summary of Contents for FAZER FZ6-SV 2006

Reviews:

Related manuals for FAZER FZ6-SV 2006

Brands by name

Popular brands

Yamaha FAZER FZ6-SV 2006, Owner'S Manual

Search results

Summary of Contents for FAZER FZ6-SV 2006

Reviews:

Related manuals for FAZER FZ6-SV 2006

Brands by name

Popular brands