Yamaha F9.9 Owner'S Manual Download Page 42 | Manualshive

Page: 42 / 112

background image

Instruments and indicators

36

EMU36016

Indicators

EMU36026

Low oil pressure-alert indicator

If oil pressure drops too low, this indicator will
light up. For further information, see page 37.

NOTICE

ECM00024



Do not continue to run the engine if the
low oil pressure-alert indicator is on and
the engine oil level is lower. Serious en-
gine damage will occur.



The low oil pressure-alert indicator does
not indicate the engine oil level. Use the
oil dipstick to check the oil level. For fur-
ther information, see page 43.

1. Low oil pressure-alert indicator

1

ZMU07820

U6DR38E0.book Page 36 Tuesday, November 27, 2018 2:08 PM

©2020

Motor

Corporation

«
...
40
41
42
43
44
...
»

Summary of Contents for F9.9

















































































































Reviews:

No comments

Related manuals for F9.9

Brand: Yamaha Pages: 82

XRP7664-65-74-75

Brand: Exar Pages: 8

Brand: Biostar Pages: 45

Cyclone IV GX FPGA

Brand: Altera Pages: 60

Brand: Phytec Pages: 128

Brand: Sapphire Audio Pages: 50

Brand: Texas Instruments Pages: 21

Brand: EPOX Pages: 84

Brand: Gigabyte Pages: 96

Brand: IBASE Technology Pages: 91

Brand: Fujitsu Siemens Computers Pages: 20

Brand: MSI Pages: 164

SBC81870 Series

Brand: AXIOMTEK Pages: 120

Brand: Atmel Pages: 59

Brand: OLIMEX Pages: 17

Brand: HONDA marine Pages: 2

Brand: Texas Instruments Pages: 24

Brand: ST Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands