Yamaha F9.9 Owner'S Manual Download

Page: 43 / 112

Engine control system

EMU26806

Alert system

NOTICE

ECM00093

Do not continue to operate the engine if an
alert device has activated. Consult your
Yamaha dealer if the problem cannot be
located and corrected.

EMU26869

Low oil pressure alert

If the oil pressure drops too low, the alert de-
vice will activate.



The engine speed will automatically de-
crease to about 2000–3500 r/min.



The low oil pressure-alert indicator will light
or blink (if equipped).



The buzzer will sound (if equipped).

If the alert system has activated, stop the en-
gine as soon as it is safe to do so. Check the
oil level and add oil as needed. If the oil level
is correct, consult your Yamaha dealer.

ZMU07904

ZMU02360

U6DR38E0.book Page 37 Tuesday, November 27, 2018 2:08 PM

Yamaha

Motor

Corporation

Summary of Contents for F9.9

















































































































Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands

Yamaha F9.9, Owner'S Manual

Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands