Yamaha F40G Owner'S Manual Download

Page: 101 / 110

Trouble Recovery

(5) Unscrew the filter cup from the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when unscrewing the filter cup.

[ECM01961]

(6) Drain the water in the filter cup by soak-

ing it up with a rag.

(7) Firmly screw the filter cup onto the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01971]

(8) Connect the water detection switch cou-

pler securely until a click is heard.

(9) Fasten the water detection switch lead

with the plastic tie.

(10)Install the top cowling.
(11)Start the engine and make sure that the

water separator-alert indicator remains
off. Have a Yamaha dealer inspect the
outboard motor after returning to port.

F40G, F70A
(1) Stop the engine.
(2) Remove the top cowling.
(3) Remove the cover.

1. Water detection switch coupler

1. Filter cup
2. Water detection switch lead

ZMU07930

ZMU07931

1. Water detection switch coupler

1. Plastic tie

ZMU07932

ZMU07933

6C1-9-7J-1E0.book 94 ページ２０１９年１０月３０日　水曜日　午後２時５６分

Summary of Contents for F40G















































































































Search results

Summary of Contents for F40G

Reviews:

Related manuals for F40G

Brands by name

Popular brands

Yamaha F40G, Owner'S Manual

Search results

Summary of Contents for F40G

Reviews:

Related manuals for F40G

Brands by name

Popular brands