Yamaha F30 Page 42 Owner'S Manual Download | Manualshive

Page: 42 / 120

background image

36

Instruments and indicators

EMU36016

Indicators

EMU36026

Low oil pressure-alert indicator

If oil pressure drops too low, this indicator will
light up. For further information, see page 44.

NOTICE

ECM00024



Do not continue to run the engine if the
low oil pressure-alert indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.



The low oil pressure-alert indicator
does not indicate the engine oil level.
Use the oil dipstick to check the oil lev-
el. For further information, see page 50.

EMU36034

Overheat-alert indicator

If the engine temperature rises too high, this
indicator will light up. For further information
on reading the indicator, see page 44.

NOTICE

ECM00053

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

EMU26494

Digital tachometer

The tachometer shows the engine speed
and has the following functions.
All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

TIP:

The water separator and engine trouble-alert
indicators only operate when the engine is
equipped with the appropriate functions.

1. Low oil pressure-alert indicator

1. Overheat-alert indicator

1. Tachometer
2. Trim meter
3. Hour meter
4. Low oil pressure-alert indicator
5. Overheat-alert indicator
6. Set button
7. Mode button

1

5

2

4

3

6

7

ZMU03601

6BG-9-3F-E0.book 36 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
40
41
42
43
44
...
»

Summary of Contents for F30

























































































































Reviews:

No comments

Related manuals for F30

Brand: Yamaha Pages: 20

Brand: Balluff Pages: 62

Brand: Udoo Pages: 9

Brand: Yamaha Pages: 86

Brand: MATSONIC Pages: 78

NORA-W10 Series

Brand: Ublox Pages: 22

Brand: IEI Technology Pages: 162

Brand: JS Automation Pages: 18

Brand: Gigabyte Pages: 36

Brand: Supermicro Pages: 111

Brand: Rosch Computer Pages: 52

TLV320AIC12KEVM-K

Brand: Texas Instruments Pages: 40

Brand: Wemos Pages: 12

Brand: ASROCK Pages: 98

Brand: Icop Pages: 30

Brand: Yamaha Pages: 82

PHANTOM GAMING X670E PG Lightning

Brand: ASROCK Pages: 66

Brand: DFI Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands