manualshive.com logo in svg

Yamaha F200D, Owner'S Manual

Share
Download
Yamaha F200D Owner'S Manual Download Page 71

Trouble Recovery

65

A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29431

Temporary action in emergency

EMU29440

Impact damage

WARNING

EWM00870

The outboard motor can be seriously dam-
aged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

1.

Stop the engine immediately.

2.

Inspect the control system and all compo-
nents for damage. Also inspect the boat
for damage.

3.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

4.

Have a Yamaha dealer inspect the out-
board motor before operating it again.

EMU29450

Running single engine

When using only engine in an emergency, be
sure to keep the unused one tilted up and op-
erate the other engine at low speed.

CAUTION:

ECM00370

If the boat is operated with one engine in
the water but not running, water may run
into the exhaust pipe due to wave action,
causing engine trouble.

NOTE:

When you are maneuvering at low speed,
such as near a dock, it is recommended that
both engines be running with one in neutral
gear if possible.

U69J14E0.book  Page 65  Friday, March 12, 2004  10:20 AM

Summary of Contents for F200D


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands