Yamaha F150G Page 44 Owner'S Manual Download | Manualshive

Page: 44 / 104

background image

Instruments and indicators

37

EMU46654

6Y8 Multifunction meters

There are two types of 6Y8 Multifunction me-
ters.



6Y8 Multifunction tachometer



6Y8 Multifunction speed & fuel meter

6Y8 Multifunction tachometer

6Y8 Multifunction speed & fuel meter

TIP:

The information displayed on the multifunc-
tion display can be changed. For information
on other settings or changing the displayed
information, see the operation manual includ-
ed with the 6Y8 Multifunction meter.

This manual mainly covers the alert display of
the 6Y8 Multifunction tachometer. See the
following sections for information about the
alert indicators.

1. Set button
2. Mode button

1. Tachometer
2. Trim meter
3. Multifunction display

SET

MODE

2

1

ZMU08407

1

2

3

ZMU08408

1. Set button
2. Mode button

1. Speedometer
2. Fuel meter
3. Multifunction display

SET

MODE

2

1

ZMU08409

1

3

2

ZMU08410

U6DV75E0.book Page 37 Tuesday, February 21, 2017 8:33 AM

«
...
42
43
44
45
46
...
»

Summary of Contents for F150G









































































































Reviews:

No comments

Related manuals for F150G

Brand: MSI Pages: 169

Brand: AOpen Pages: 8

Brand: P&E Microcomputer Systems Pages: 53

EMB-APL1-A10-3350-F1-LV

Brand: Aaeon Pages: 42

Brand: Linear Technology Pages: 10

Brand: DFI Pages: 60

WAFER-CV-N26001

Brand: IEI Technology Pages: 135

PX845EV1 Series

Brand: Albatron Pages: 56

GA-MA785GMT-UD2H

Brand: Gigabyte Pages: 104

Brand: Aaeon Pages: 56

Brand: SOYO Pages: 94

Brand: Bartels Mikrotechnik Pages: 9

Brand: JETWAY Pages: 46

Brand: Texas Instruments Pages: 24

Z68A-G43 G3 Series

Brand: MSI Pages: 152

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 64

Brand: Yamaha Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands