manualshive.com logo in svg

Yamaha F150A2, Owner'S Manual

Share
Download
Yamaha F150A2 Owner'S Manual Download Page 60

Operation

54

connected, cooling water can leak out and
the engine can overheat during operation.

[ECM01802]

EMU36942

Install cowling

1.

Be sure that all cowling lock levers are
released.

2.

Be sure that the rubber seal is seated all
the way around the engine.

3.

Place the cowling on top of the seal.

4.

Check to be sure it fits properly in the
rubber seal.

5.

Move the levers to lock the cowling as
shown. 

NOTICE:

 If the top cowling is

not installed correctly, water spray
under the top cowling can damage the
engine, or the top cowling can blow
off at high speeds.

 [ECM01992]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

EMU2915A

Checking power trim and tilt system

WARNING

EWM01931

Never get under the lower unit while it is
tilted, even when the tilt support lever is
locked. Severe injury could occur if the
outboard motor accidentally falls.

Body parts can be crushed between the
motor and the clamp bracket when the
motor is trimmed or tilted.

Be sure no one is near the outboard mo-
tor before performing this check.

1.

Check the power trim and tilt unit for any
sign of oil leaks.

1. Fitting
2. Flushing device

ZMU06159

1

2

ZMU06131

ZMU06132

U63P3FE0.book  Page 54  Thursday, December 5, 2013  10:01 AM

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F150A2













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands