background image

Basic Operation

15

EMX860ST—Owner’s Manual

Basic Operation

Connecting microphones 
and instruments

1

Before connecting mics or instruments, 
make sure that the power of all equip-
ment (where applicable) is turned off. 
Also make sure that the level controls of 
each channel of the EMX860ST and the 
MASTER control of the MAIN section are 
turned down.

2

Connect cables to your mics and instru-
ments, and insert the other end of the 
cable firmly into the appropriate Lo-Z/Hi-
Z jack (channels 1–6) or the MIC/LINE 
jack (channels 7–8).

3

Turn the power on in the order of periph-
eral devices 

 EMX860ST.

4

Set the MAIN section MASTER control to 
the 

 position.

Adjusts the stereo image of each channel using 
the PAN controls. (Adjust the balance between 
the left and right volume levels of the sound 
sources connected to the LINE connectors L/R 
for channels 7 and 8 using the BAL/PAN con-
trols.)

5

While speaking into the mic (while play-
ing the instrument), adjust the channel 
LEVEL control so that the 0 LED of the 
MAIN section peak level meter lights 
occasionally.

6

If you wish to adjust the tone of each 
channel, rotate the equalizer controls as 
desired.

7

Use the MAIN section graphic equalizer 
and MASTER control to adjust the overall 
volume and tone.

Sending an independent 
mix to the monitor speakers

1

Set the MONITOR section MASTER con-
trol to the 

 position.

2

Adjust the MONI control to increase the 
level of the channel you want to hear 
from the monitor speaker, and also adjust 
so that the peak level meter 0 LED of the 
monitor section lights up occasionally.

3

Use the graphic equalizers and MASTER 
controls of the MAIN/MONITOR sections 
to adjust the overall volume and tone.

Using the digital effect

The EMX860ST has a built-in digital effect, 
allowing reverberation or ambiance to be added 
to vocals or instrumental sounds.

1

Connect a mic or instrument to the 
desired channels, and adjust the volume 
and tone.

2

Press the DIGITAL EFFECT ON switch of 
the DIGITAL EFFECT section.

3

Use the effect select switches of the DIGI-
TAL EFFECT section to select the effect 
type.

VOCAL ...... Reverb appropriate for vocals.

L. HALL...... Reverb typical of a large hall.

S. HALL...... Reverb typical of a small hall.

4

Raise the EFFECT control of the channels 
to which you wish to apply the digital 
effect.

5

Use the MAIN/MONITOR section EFFECT 
RTN control to adjust the level of the 
sound processed by the effect.

Note:   When connecting a line level device to 
channels 1–6, turn on the PAD switch.
You cannot use a channel’s Lo-Z and Hi-Z 
jacks, and MIC and LINE jacks at the same 
time. 

Note:   When turning the power off, reverse this 
sequence.

Note:   The MONI controls are not affected by 
the level settings of each channel. This allows 
you to create a mix that is independent of the 
MAIN section.

Note:   If the effect sound is distorted even if the 
EFFECT RTN is turned all the way down, lower 
the EFFECT controls of each channel.

Summary of Contents for EMX860ST

























Reviews: