Yamaha EF6300iSDE - 5500 Watt Inverter Generator Owner'S Manual Download Page 12 | Manualshive

Page: 12 / 60

background image

763-119

q

w

e

– 7 –

700-7XF

AE00111

Oil warning light (red)

When the oil level falls below the lower level, the oil
warning light comes on and then the engine stops
automatically. Unless you refill with oil, the engine will
not start again.

NOTE:

If the engine stalls or does not start, turn the engine
switch to “START”. If the oil warning light comes on,
the engine oil is insufficient. Add oil and restart.

AE00101

CONTROL FUNCTION

AE00121

Engine switch

The engine switch controls the ignition system.

1

7

“ON”

Ignition circuit is switched on.
The engine can be started.

2

5

“STOP”

Ignition circuit is switched off.
The engine will not run.

3

6

“START”

Starting circuit is switched on.
The starter motor starts and the engine can be started.
Take your hand off the switch immediately after the
engine starts.

7CK-28199-10_a 08.9.15 17:47 Page 7

«
...
10
11
12
13
14
...
»

Summary of Contents for EF6300iSDE - 5500 Watt Inverter Generator





























































Reviews:

No comments

Related manuals for EF6300iSDE - 5500 Watt Inverter Generator

Brand: Harmonic Pages: 27

Brand: YASKAWA Pages: 128

Industrial Series VEC023

Brand: Vector Pages: 8

Brand: Sima Pages: 2

MONO MIXER SERIES

Brand: Audioplex Pages: 1

Brand: Magnimage Pages: 40

Brand: APS Pages: 70

Brand: RGBlink Pages: 46

Brand: CEL-MAR Pages: 28

Brand: M-system Pages: 4

Brand: Audio Nemesis Pages: 10

CompactGROUND GS10plus

Brand: AEROCOMPACT Pages: 27

Helios III Series

Brand: CNBOU Pages: 27

Brand: Ediseja 21 Pages: 22

Brand: R&S Pages: 24

Brand: Mobotix Pages: 44

Brand: Peak Pages: 37

Brand: C&C TECHNIC TAIWAN CO., LTD. Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands