18
DTXPRESS
T–11. Panel Switch
Initial Display
11
SW
This test checks the panel switches.
Press the panel switches one by one from [PLAY] to
[VALUE+] button in the order displayed on the LCD.
The test orders are as follows:
11
SW
[PLAY]
[PLAY], [UTIL.], [CLICK], [TRIG.], [VOICE]
[SONG], [START], [SAVE/], [SHIFT], [PAGE–]
[SEL <], [VAL–], [PAGE+], [SEL>], [VAL+]
Result Screens
OK: It proceds to the next test automatically
NG
11
SW
FAIL
Test End
OK: It proceeds to the next test automatically.
If an error is detected during the test, refer to section B,
[PROCEEDING THROUGH THE TEST].
T–12. Attenuator Switch IN 01
T–13. Attenuator Switch IN 02
T–14. Attenuator Switch IN 03
T–15. Attenuator Switch IN 04
T–16. Attenuator Switch IN 05
T–17. Attenuator Switch IN 06
Initial Display
12
ATT. SW IN01
waiting
too Lo
Flip the attenuator switch to the down position. (Switch
SW1-6 to the down position.)
Insert one end of, the stereo cable into the PHONES jack
and the other into the 1.KICK jack. Then check whether
there is signal leakage from any of the other inputs.
OK
13
ATT. SW IN02
waiting
When the next attenuator switch number appears in the
display (e.g. IN02), insert the appropriate end of the stereo
cable into the relevant jack (e.g. 2.SNARE). Repeat this
process for all remaining switches.
Result Screens
OK: It proceds to the next test automatically
NG
12
ATT. SW IN01
FAIL
Test End
OK: It proceeds to the next test automatically.
If an error is detected during the test, refer to section B,
[PROCEEDING THROUGH THE TEST].
T–18. TRIGGER IN 01: 1 KICK
T–19. TRIGGER IN 02: 2 SNARE
T–20. TRIGGER IN 03: 3 TOM1
T–21. TRIGGER IN 04: 4 TOM2
T–22. TRIGGER IN 05: 5 TOM3
T–23. TRIGGER IN 06: 6 RIDE
T–24. TRIGGER IN 07: 7 CRASH
T–25. TRIGGER IN 08: 8 HIHAT
T–26. TRIGGER IN 09: 9/10
T–27. TRIGGER IN 10: 9/10
Initial Display
18
TRIGGER IN01
waiting
too Lo
Flip the attenuator switch to the down position. (Switch
SW1-6 to the down position.)
Insert one end of, the stereo cable into the PHONES jack
and the other into the 1.KICK jack. Then check whether
there is signal leakage from any of the other inputs.
OK
19
TRIGGER IN02
waiting
too Lo
When the next attenuator switch number appears in the
display (e.g. IN02), insert the appropriate end of the stereo
cable into the relevant jack (e.g. 9/10). Repeat this process
for all remaining switches.
Result Screens
OK: It proceeds to the next test automatically.
NG
18
TRIGGER IN01
FAIL XXXXX
(XXXXXX= too High; too Lo; XtalkIN 2; BAD curve)
Summary of Contents for DTXPRESS
