E-
68
REMOTE CONTROL FEATURES
Programming a new remote control function (Learn feature)
If you want to program functions not included in the basic operations covered by the manufacturer code, or a manufacturer code is not
available, the following procedure needs to be performed. The possible programming area is the same as a component control area, so the
buttons are programmable independently for each source component area.
TRANSMIT
RE–NAME
CLEAR
LEARN
MACRO
OFF
ON
MACRO
SYSTEM
POWER
STANDBY
V–AUX
TUNER
PHONO
CABLE
SAT
MD/TAPE
CD–R
CD
D–TV/LD
VCR 1
VCR 2
VCR3/DVR
DVD
6CH INPUT
TITLE
SOURCE
SEARCH
POWER
STOP
PAUSE
PLAY
REC
CHAPTER
SELECT
10KEY
DSP
HALL 1
HALL 2
CHURCH
JAZZ CLUB
ROCK
CONCERT
ENTER–
TA NMENT
CONCERT
V DEO 1
CONCERT
V DEO 2
ENTER
DISPLAY
MENU
SOUND
1
2
3
4
4, 8
2
1
1
1
Set 10KEY/DSP to 10KEY.
Caution
• It is also possible to program in the control area of this unit
with
10KEY/DSP
set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
2
2
Press an input selector button to select a source
component.
3
3
Place this remote control and the other remote
control about 5 to 10 cm apart on a flat surface so
that their infrared transmitters are aimed at each
other.
4
4
Press LEARN by using a ballpoint pen or similar
object.
“LEARN” and the selected component name appear alternately
in the display window.
10KEY
DSP
TRANSMIT
RE
–NAME
CLEAR
LEARN
MACRO
OFF
ON
MACRO
SYSTEM
POWER
ST
ANDBY
V
–
AUX
TUNER
PHONO
CABLE
SA
T
MD/T
A
PE
CD
–
R
CD
D
–
TV/LD
VCR 1
VCR 2
VCR3/DVR
DVD
6CH INPUT
TITLE
5 to 10 cm (2 to 4 inch)
LEARN
LEARN
DVD
Cautions
• If you do not press any button within 30 seconds during steps
5 and 6, the learning process is canceled. If this happens, start
over from step 4.
• Do not press and hold
LEARN
longer than 3 seconds.
Otherwise this unit enters the manufacturer code setting
mode.
5
5
Press the button for which you want to program the
new function.
“LEARN” is displayed.
6
6
Press and hold the button on the other remote
control that has the function you want to program
into this remote control until “OK” appears in the
display window.
Cautions
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 5.
• When the memory is full, “FULL” appears in the display
window, and this remote control cannot acquire any more
functions. Clear unnecessary programmed functions to allow
the unit to acquire new functions.
7
7
Repeat steps 5 and 6 to program additional func-
tions.
8
8
Press LEARN again to exit from the learning mode.
Cautions
• Learning may not be possible in the following cases:
1
when the batteries in the remote control for this unit or other
component are weak
2
when the distance between the two remote controls is too
much or too little
3
when the remote control infrared windows are not facing with
appropriate angle
4
when the remote control is exposed to the direct sunlight
5
when the function to be programmed is continuous or
uncommon
• “ERROR” appears in the display window in the following
circumstances:
1
when pressing more than one button at once
2
when
MACRO ON/OFF
is switched to another position
LEARN
