108
DGX-620/520, YPG-625/525 Owner’s Manual
Accessory CD-ROM Installation Guide
Installing the driver on Windows 98/Me
1
Start the computer.
2
Insert the supplied CD-ROM into the CD-
ROM drive. A start window will appear
automatically.
3
First, make sure the POWER switch on
the instrument is set to OFF, then use a
USB cable to connect the USB terminal of
the computer to the USB connector of the
instrument. When the instrument is
turned on, the computer automatically
displays the “Add New Hardware Wizard.
Otherwise, refer to “Troubleshooting” in
the “Accessory CD-ROM Installation
Guide” section of the Owner’s Manual.
For Windows Me users, check the radio button to
the left of “Automatic search for a better driver
(Recommended)” and click [Next]. The system
automatically starts searching and installing the
driver. Proceed to Step 8. If the system does not
detect the driver, select “Specify the location of
the driver (Advanced)” and specify the CD-ROM
drive’s root directory to install the driver and click
[Next]. Execute the installation by following the
onscreen instructions and proceed to Step 8.
4
Click [Next].
The window enables you to select the search
method.
5
Check the radio button to the left of
“Search for the best driver for your
device. (Recommended)”. Click [Next].
The window enables you to select a location in
which to install the driver.
6
Check the “Specify a location” box, click
“Browse..”, then specify the root direc-
tory of the CD-ROM drive and continue
the installation. The CD-ROM drive letter
may vary depending on your computer’s
configuration.
7
When the system detects the driver on
the CD-ROM and is ready for installation,
it is shown as a message on the screen.
Make sure that the “YAMAHA USB MIDI
Driver” is listed, and click [Next]. The sys-
tem starts the installation.
8
When installation is complete, a message
indicating so appears. Click [Finish].
The driver has been installed.
Installing the driver on Windows 2000
1
Start the computer and use the “Adminis-
trator” account to log into Windows 2000.
2
Select [My Computer]
➔
[Control Panel]
➔
[System]
➔
[Hardware]
➔
[Driver Sign-
ing]
➔
[File Signature Verification], and
check the radio button to the left of
“Ignore—Install all files, regardless of file
signature” and click [OK].
3
Insert the supplied CD-ROM into the CD-
ROM drive. A start window will appear
automatically.
4
First, make sure the POWER switch on the
MIDI device is set to OFF, then use a USB
cable to connect the MIDI device to the
computer. After making the connections,
turn on the power of the MIDI device. The
system automatically launches the Found
New Hardware Wizard.
Otherwise, refer to “Troubleshooting” in the
“Accessory CD-ROM Installation Guide” section
of the Owner’s Manual. Click [Next]. (Some
computers may take a while to display the Wizard
window.)
5
Select the radio button for “Search for a
suitable driver for my device [recom-
mended]”, then click [Next].
6
Check the “CD-ROM drives” check box,
deselect all other check boxes, then click
[Next].
7
Deselect the “Install one of the other driv-
ers”, then click [Next].
8
When the installation is complete, the
Wizard displays “Completing the Found
New Hardware Wizard”.
Click [Finish]. (Some computers may take a
while to display the Wizard window.)
9
Restart the computer.
The USB-MIDI driver installation is complete.
• If you are using Windows Me, skip Step 4–7.
NOTE
• Some computers may take about ten seconds to show this screen
after the installation is complete.
NOTE
• If the Wizard panel informs you that “The software you are about to
install does not contain a Microsoft digital signature”, click [Yes].
NOTE
• If the system prompts you to insert the Windows CD-ROM during
detection of the drivers, point to the “USBdrv2k_” folder (e.g.,
D:\USBdrv2k_) and continue the installation.
NOTE
