background image

10

Appendix

DA824—Owner’s Manual

Appendix 

Specifications

Sampling rate

MY8-AE, MY8-TD

39.69–50.88 kHz

MY8-AT

41.013–50.88 kHz

DA conversion resolution

24-bit linear, 128-times oversampling 

Frequency response

–3, +1 dB, 20 Hz–20 kHz

Dynamic Range

1

1. Measured with a 6 dB/octave filter at 12.7 kHz; equivalent to a 20 kHz filter with infinite 

dB/octave attenuation.

110 dB (typical)

Gain Error

±1 dB @ 1 kHz 

THD

2

2. 6 dB/octave filter @ 80 kHz.
 * Where dB represents a specific voltage, 0 dB is referenced to 0.775 V rms, 0 dBV is refer-

enced to 1.00 V rms.

0.05%, 20 Hz–20 kHz

0.01% full scale output @ 1 kHz

Hum & Noise Level

1

–92 dBu (typical)

Crosstalk

–70 dB between adjacent channels @ 1 kHz

Signal Delay

0.57 ms (digital input to analog output, fs = 48 kHz)

Indicators

PEAK

3 dB below full scale

NOMINAL

14 dB below full scale

SIGNAL

34 dB below full scale

LOCK

Wordclock lock

POWER

Power on/off

Power requirements

U.S.A. & Canada 120 V AC, 60 Hz
Europe 230 V AC, 50 Hz

Power consumption

40 W

Dimensions (W 

×

 H 

×

 D)

480 

×

 97.5 

×

 366.8 mm (18.9 x 3.84 x 14.44 inches)

Weight

7.5 kg (16.53 lbs)

Free-air operating temperature

10˚ C to 35˚ C (50˚ F to 95˚ F)

Storage temperature

–20˚ C to 60˚ C (–4˚ F to 140˚ F)

Power cord length

1.9 m

Supplied Accessories

Owner’s Manual

Summary of Contents for DA824





















Reviews: