manualshive.com logo in svg

Yamaha CRW4001t, User Manual

Share
Download
Yamaha CRW4001t User Manual Download Page 22

Appendix

16

Specifications

Specifications are subject to change without prior notice.

Interface

ATAPI/IDE

Data Capacity

1.2m/sec: 666MB

1.4m/sec: 540MB

Record/Read Speed

Writing (CD-RW): 2X speed

Writing (CD-R): Normal speed, 2X speed, 4Xspeed

Reading: Normal speed, 2X speed, 4X speed, 6X speed

Data Transfer Rate

6xS: 900KB/sec

4xS: 600KB/sec

2xS: 300KB/sec

1xS: 150KB/sec

Burst Transfer Rate

5.5MB/sec

Buffer Size

2MB (500 sectors)

Access Speed

250ms

Installation

Horizontal

Disc Loading

Tray

Audio Out

Frequency Response

20 - 20,000Hz (Line Out)

(normal speed)

Output Level

1 Vrms (Line Out)

Power Consumption

11W (read/write)

Power Supply

5V 

±

5%, 12V 

±

10%

Environment

Temperature: +5

°

C - +40

°

C (read/write, when used in 

a fan-cooled system)

Humidity: 25 - 80%

Dimensions (WxHxD)

146 x 41.3 x 203 mm

Weight

1.3kg

Rear Panel

Connector

IDE/Power Supply

Non-shielded two-in-one, 40p + 4p

MASTER/SLAVE/CSEL Selector Short-pin 6p

Audio Out

MOLEX 53532-04

Summary of Contents for CRW4001t

























Reviews:

No comments

Brands by name

Popular brands

Load more brands