Yamaha Crux S Workshop Manual Download Page 177

Page: 177 / 209

CHAS

L-176

STEERING HEAD AND HANDLEBAR

STEERING INSPECTION

1. Wash the Bearing and Ball Races with a sol-

vent

2. Inspect :

• Bearing Races ¿

• Ball races À

Pitting/Damage Ÿ Replace

ææææææææææææææææææææææææææææææææææ

Bearing Race replacement steps :

• Remove the Ball Races on the Head Pipe us-

ing Long Rod ¿ and the hammer as shown

• Remove the Ball Race on the Under Bracket

using the floor chisel À and the hammer as

shown

• Install the new Dust Seal and Races

ææææææææææææææææææææææææææææææææææ

NOTE :

Always replace Bearing races as a set.

STEERING INSTALLATION

Reverse the “REMOVAL”procedure

Note the following points

1. Lubricate

• Balls (upper and lower)

• Ball Races

2. Install :

• Ring Nut (lower) ¿

• Damper Rubber À

• Ring Nut (upper) Á

• Lock Washer Â

Refer to “STEERING HEAD

INSPECTION” section in Chapter 3, Page

no 3-22

3. Install :

• Bush

• Meter Assembly with Handle Crown

6-30

WARNING

CAUTION:

If Bearing Race is not fitted squarely, the

Head Pipe could be damaged.

Recommended lubricant

Lithium - soap base grease

Ring Nut:

15.5 Nm (1.55 m.kg, 11.2 ft.lb)

Summary of Contents for Crux S


















































































































































































































Search results

Summary of Contents for Crux S

Reviews:

Brands by name

Popular brands

Yamaha Crux S, Workshop Manual

Search results

Summary of Contents for Crux S

Reviews:

Brands by name

Popular brands