Yamaha CP5, Data List

Page: 25 / 42

CP5 / CP50 Data List
25
Effect Parameter List for Other Group
Category — COMPRESSOR
[1] CLASSIC COMPRESSOR
[2] MULTI BAND COMP
When the value of Bottom is greater than Top, the sound will not be modulated and only the Bottom
value is available.
Category — Lo-Fi
[1] LO-FI
[2] NOISY
[3] DIGITAL TURNTABLE
Category — TEC
[1] RING MODULATOR
[2] DYNAMIC RING MODULATOR
No. Parameter Range Value Control
1 Attack 1ms – 40ms (0 – 19)
2 Release 10ms – 680ms (0 – 15)
3 Threshold -48dB – -6dB (79 – 121)
4 Ratio 1 – 20.0 (0 – 7)
5 Output Level 0 – 127 (0 – 127)
6 —
7 —
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Control
1 Low Attack 1ms – 200ms (0 – 29)
2 Low Threshold -54dB – -6dB (73 – 121)
3 Low Ratio 1 – 20.0 (0 – 7)
4 Low Gain -∞ – +18dB (0 – 55)
5 Mid Attack 1ms – 200ms (0 – 29)
6 Mid Threshold -54dB – -6dB (73 – 121)
7 Mid Ratio 1 – 20.0 (0 – 7)
8 Mid Gain -∞ – +18dB (0 – 55)
9 High Attack 1ms – 200ms (0 – 29)
10 High Threshold -54dB – -6dB (73 – 121)
11 High Ratio 1 – 20.0 (0 – 7)
12 High Gain -∞ – +18dB (0 – 55)
13 Divide Freq Low 16Hz – 20kHz (0 – 124)
14 Divide Freq High 16Hz – 20kHz (0 – 124)
15 Common Release 10msec – 3000msec (0 – 23)
16 —
No. Parameter Range Value Control
1 Sampling Freq. Control 44.1 – 344Hz (0 – 127)
2 Word Length 1 – 127 (1 – 127)
3 Output Gain -6dB – +36dB (0 – 42)
4 Pre-LPF Cutoff Frequency 63Hz – 20.0kHz (10 – 60)
5 Filter Type thru, Power Bass, Radio,
Telephone, Clean, Low (0 – 5)
6 Pre-LPF Resonance 1 – 12.0 (10 – 120)
7 Bit Assign 0 – 6 (0 – 6)
8 Emphasis off/on (0 – 1)
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)

11 —
12 —
13 —
14 —
15 Input Mode mono, stereo (0 – 1)
16 —
No. Parameter Range Value Control
1 Mod Depth 0 – 10 (0 – 10)

2 Mod Speed 0 – 127 (0 – 127)
3 Mod Feedback -63 – +63 (1 – 127)
4 Mod Mix Balance 1 – 127 (1 – 127)
5 Drive 0 – 127 (0 – 127)
6 AM Speed 0.00Hz – 39.7Hz (0 – 127)
7 AM Depth 0 – 127 (0 – 127)
8 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60)
9 LPF Resonance 1.0 – 12.0 (10 – 120)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 EQ Frequency 100Hz – 10.0kHz (14 – 54)
12 EQ Gain -12 – +12dB (52 – 76)
13 EQ Width 1.0 – 12.0 (10 – 120)
14 —
15 —
16 —
No. Parameter Range Value Control
1 Click Density 0 – 5 (0 – 5)
2 Click Level 0 – 127 (0 – 127)
3 Noise Tone 0 – 6 (0 – 6)
4 Noise Mod Speed 0.00Hz – 39.7Hz (0 – 127)

5 Noise Mod Depth 0 – 127 (0 – 127)
6 Dry Send to Noise 0 – 127 (0 – 127)
7 Noise LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60)
8 Noise LPF Q 1.0 – 12.0 (10 – 120)
9 Noise Level 0 – 127 (0 – 127)
10 —
11 Dry Level 0 – 127 (0 – 127)
12 Dry LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60)
13 —
14 —
15 —
16 —
No. Parameter Range Value Control
1 OSC Frequency Coarse 0.5 – 5kHz (0 – 127)

2 OSC Frequency Fine 0 – 127 (0 – 127)
3 LFO Wave tri, sine (0 – 1)
4 LFO Depth 0 – 127 (0 – 127)
5 LFO Speed 0.0Hz – 39.70Hz (0 – 127)
6 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52)
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60)
8 —
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 22.
No. Parameter Range Value Control
1 Sensitivity 0 – 127 (0 – 127)

2 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52)
3 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60)
4 Attack Time 0.3ms – 227ms (0 – 127)
5 Release Time 2.6ms – 2171ms (0 – 127)
6 Release Curve 0 – 127 (0 – 127)
7 Direction up, down (0 – 1)
8 Dyna Threshold Level 0 – 127 (0 – 127)
9 Dyna Level Offset 0 – 127 (0 – 127)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 22.