Yamaha CDC-697 Service Manual Download

Page: 18 / 46

CDC-697

c) Operates as if no disc loaded.

(although loaded)

d) Sound skips.

(Time display fails to advance properly)

e) No search provided.

(Sound skipped after search)

Disc clamp defective.
CLAMP switch defective.
Microprocessor (IC309)
defective.

YES

Does disc clamp

operate properly?

IC1 or IC3 defective.
Microprocessor (IC309)
defective.

YES

Infrared sensor defective.
Microprocessor (IC309)
defective.

Does table

rotate properly?

YES

Is table position
sensor normal?

Poor table rotation.

YES

Is FOCUS

lock done?

YES

Is pick-up at

innermost position?

YES

Jitter defective.

Does spindle

motor run?

YES

Is EFM signal

normal?

SPINDLE servo system
defective.

FEED LIMIT switch
defective.

FOCUS servo system
defective.

TRACKING servo system defective.
FEED servo system defective.
FOCUS servo system defective.
Pick-up defective.

Is disc dirty,

scratched or

warped?

YES

Is disc or disc

stabilizer in contact with

mechanism?

YES

Check by using a
known good disc.

Poor mechanism
accuracy.
Floating rubber/spring
deformed.
Pick-up connector
assembly caught.

IC1 or IC3 defective.

Is disc dirty,

scratched or

warped?

YES

Is TER

waveform normal?

YES

Check by using a known
good disc.

TRACKING servo system
defective.
FEED servo system defective.
FOCUS servo system defective.
Pick-up defective.

Summary of Contents for CDC-697















































Search results

Summary of Contents for CDC-697

Reviews:

Related manuals for CDC-697

Brands by name

Popular brands

Yamaha CDC-697, Service Manual

Search results

Summary of Contents for CDC-697

Reviews:

Related manuals for CDC-697

Brands by name

Popular brands