Yamaha AN200 Editor Manual Download | Manualshive

Page: 17 / 72

background image

17

Parameters /

AN200 Editor Main Window

LFO Parameter Blocks

The LFO parameters allow you to create a wide variety of modulation effects, using a low
frequency signal to regularly change the pitch, volume or timbre of the pattern. The LFO
can be used to make the sound warmer and more natural, or can be used to produce
wild special effects.

LFO 1 and LFO 2 can also be used as control sources (in

Sync Pitch Control

, etc.), giving you even greater editing flexibility.

• Depending on the setting of the selected pattern's

Assign Group

parameter, the LFO 1 and

LFO 2 blocks in the display may be different, with different sets of parameters. All LFO
parameters below are available on either LFO 1 or LFO 2; however, some parameters will only
be available on one of the LFO blocks, while the other block will have a limited parameter set.

•

LFO 1 / LFO 2 DETAIL Page

• LFO 1 / LFO 2 WAVE

Settings:

Sine,

Sine Ofst1 (Offset 1), Sine Ofst2, Sine180 Ofst1, Sine180 Ofst2

Triangle,

Triangle Ofst1, Triangle Ofst2, Triangle180 Ofst1, Triangle180 Ofst2

Square,

Square Ofst2, Square180 Ofst2

Saw Down,

Saw Down Ofst2, Saw Up, Saw Up Ofst2

S/H (Sample & Hold),

S/H Ofst2, S/H2, S/H2 Ofst2

• Parameter settings in italics above can only be selected by using the DATA DEC/INC buttons,

or by holding [shift] on the computer keyboard and using the cursor keys.

This determines the type of wave for LFO 1 or LFO 2. (The same settings are available
for both.) The wave set here determines the characteristics of the modulation applied to
the VCO (vibrato), VCF (wah) and VCA (tremolo).

• LFO 1 / LFO 2 SPEED

Range: 1 ... 256

This determines the speed of LFO 1 or LFO 2. (This parameter is the same for both.)
Higher values result in a faster LFO modulation. This is a global control in that it affects
all modulation destinations (VCO 1/2, VCA, VCF) equally.

• LFO 1 / LFO 2 VCO1

(LFO 1 / LFO 2 to VCO 1 – Oscillator 1 Pitch Modulation Depth)

• LFO 1 / LFO 2 VCO2

(LFO 1 / LFO 2 to VCO 2 – Oscillator 2 Pitch Modulation Depth)

Range: -127 ... +127

This determines the degree to which the LFO 1 or LFO 2 affects the selected oscillator's
pitch. This produces a vibrato effect, or a quavering, vibrating sound in the pattern, by
regularly modulating the pitch. Higher values result in a stronger, more pronounced
vibrato sound.

«
...
15
16
17
18
19
...
»

Summary of Contents for AN200 Editor









































































Reviews:

No comments

Related manuals for AN200 Editor

Brand: M-Audio Pages: 32

BREEZE-MANAGING EXTERNAL BREEZE REPORTS

Brand: MACROMEDIA Pages: 18

Brand: COMPRO Pages: 36

DEVICE FILTER MAC

Brand: FARONICS Pages: 30

Brand: DigiDesign Pages: 39

Brand: Ulead Pages: 80

Brand: Acroprint Pages: 68

Brand: Access Pages: 16

Brand: GRASS VALLEY Pages: 2

Brand: GRASS VALLEY Pages: 24

AURORA INGEST - S AND UPGRADE INSTRUCTIONS V7.1

Brand: GRASS VALLEY Pages: 66

DIRECTOR MX 2004-GETTING STARTED WITH...

Brand: MACROMEDIA Pages: 68

Brand: UMAX Technologies Pages: 127

ACCULINK 7800-D1-999

Brand: Paradyne Pages: 11

Brand: Waves Pages: 16

ThinkCentre M90z

Brand: Lenovo Pages: 288

Brand: AMX Pages: 84

ANTIVIR SHAREPOINT

Brand: AVIRA Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands